E234, E234n
User’s Reference
May 2004
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,
registered in the United States and/or other countries.
© 2003 Lexmark International, Inc. All rights reserved.
740 West New Circle Road
Lexington, Kentucky 40550
How to load the manual feeder .................................................................... 24
How to use the rear exit ............................................................................... 25
How to clear paper jams............................................................................... 26
How to manually feed a print job.................................................................. 30
How to print a booklet................................................................................... 35
How to print a poster .................................................................................... 36
How to print on letterhead ............................................................................ 37
How to cancel a print job.............................................................................. 38
How to add a memory card .......................................................................... 44
How to install a 550-sheet drawer................................................................ 45
Overview of the operator panel .................................................................... 48
Operator panel codes................................................................................... 54
Primary codes ........................................................................................ 54
Secondary error codes ........................................................................... 66
Configuration menus overview..................................................................... 78
Network menu ........................................................................................ 79
Parallel menu ......................................................................................... 80
Contents
3
How to install drivers for local printing.......................................................... 83
Macintosh (Web) .................................................................................... 85
How to print a test page ............................................................................... 88
How to configure for TCP/IP......................................................................... 89
How to print a test page ......................................................................... 94
Macintosh (Web) .................................................................................... 95
Using the Local Printer Settings Utility ......................................................... 99
How to conserve supplies .......................................................................... 101
How to change a toner cartridge ................................................................ 104
Lexmark Return Program........................................................................... 107
Recycling Lexmark products ...................................................................... 107
General problems....................................................................................... 112
Print quality problems................................................................................. 114
Contents
4
Notices
of publications related to this product by calling 1-800-553-9727. In
the United Kingdom and Eire, call +44 (0)8704 440 044. In other
countries, contact your point of purchase.
Section
Page
References in this publication to products, programs, or services do
not imply that the manufacturer intends to make these available in
all countries in which it operates. Any reference to a product,
program, or service is not intended to state or imply that only that
product, program, or service may be used. Any functionally
equivalent product, program, or service that does not infringe any
existing intellectual property right may be used instead. Evaluation
and verification of operation in conjunction with other products,
programs, or services, except those expressly designated by the
manufacturer, are the user’s responsibility.
© 2004 Lexmark International, Inc.
All rights reserved.
UNITED STATES GOVERNMENT RIGHTS
This software and any accompanying documentation provided
under this agreement are commercial computer software and
documentation developed exclusively at private expense.
Trademarks
Edition notice
Lexmark and Lexmark with diamond design are trademarks of
Lexmark International, Inc., registered in the United States and/or
other countries.
Edition: May 2004
PictureGrade is a trademark of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company.
PCL is Hewlett-Packard Company’s designation of a set of printer
commands (language) and functions included in its printer
products. This printer is intended to be compatible with the PCL
language. This means the printer recognizes PCL commands used
in various application programs, and that the printer emulates the
functions corresponding to the commands.
PostScript® is a registered trademark of Adobe Systems
Incorporated. PostScript 3 is Adobe Systems’ designation of a set
of printer commands (language) and functions included in its
software products. This printer is intended to be compatible with the
PostScript 3 language. This means the printer recognizes
PostScript 3 commands used in various application programs, and
that the printer emulates the functions corresponding to the
commands.
The following paragraph does not apply to any country where
such provisions are inconsistent with local law: LEXMARK
INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of
express or implied warranties in certain transactions; therefore, this
statement may not apply to you.
This publication could include technical inaccuracies or
typographical errors. Changes are periodically made to the
information herein; these changes will be incorporated in later
editions. Improvements or changes in the products or the programs
described may be made at any time.
Comments about this publication may be addressed to Lexmark
International, Inc., Department F95/032-2, 740 West New Circle
Road, Lexington, Kentucky 40550, U.S.A. In the United Kingdom
and Eire, send to Lexmark International Ltd., Marketing and
Services Department, Westhorpe House, Westhorpe, Marlow
Bucks SL7 3RQ. Lexmark may use or distribute any of the
information you supply in any way it believes appropriate without
incurring any obligation to you. You can purchase additional copies
Details relating to compatibility are included in the Technical
Reference.
Other trademarks are the property of their respective owners.
Notices
6
Licensing notice
Laser notice
The printer resident software contains:
The printer is certified in the U.S. to conform to the requirements of
DHHS 21 CFR Subchapter J for Class I (1) laser products, and
elsewhere is certified as a Class I laser product conforming to the
requirements of IEC 60825-1.
Class I laser products are not considered to be hazardous. The
printer contains internally a Class IIIb (3b) laser that is nominally a
5 milliwatt gallium arsenide laser operating in the wavelength region
of 770-795 nanometers. The laser system and printer are designed
so there is never any human access to laser radiation above a
Class I level during normal operation, user maintenance, or
prescribed service condition.
•
•
Software developed and copyrighted by Lexmark
Lexmark modified software licensed under the provisions of
the GNU General Public License version 2 and the GNU
Lesser General Public License version 2.1
Software licensed under the BSD license and warranty
statements
•
Click the title of the document you want to review:
The United Kingdom
Telecommunications Act 1984
The Lexmark modified GNU licensed software is free software; you
can redistribute it and/or modify it under the terms of the licenses
referenced above. These licenses do not provide you any rights to
the Lexmark copyrighted software in this printer.
Since the GNU licensed software that the Lexmark modifications
are based upon is supplied explicitly without warranty, use of the
Lexmark modified version is similarly provided without warranty.
See the warranty disclaimers in the referenced licenses for
additional details.
This apparatus is approved under the approval number
NS/G/1234/J/100003 for the indirect connections to the public
telecommunications systems in the United Kingdom.
Conventions
To obtain source code files for the Lexmark modified GNU licensed
software, launch the drivers CD that shipped with your printer and
click Contact Lexmark.
Note: A note identifies something that could help you.
CAUTION: A caution identifies something that could cause you
harm.
Warning: A warning identifies something that could damage your
product hardware or software.
Safety information
•
If your product is not marked with this symbol
, it must be
connected to an electrical outlet that is properly grounded.
CAUTION: Do not set up this product or make any electrical
or cabling connections, such as the power cord or telephone,
during a lightning storm.
The power cord must be connected to an electrical outlet that
is near the product and easily accessible.
Electronic emission notices
Federal Communications Commission (FCC)
compliance information statement
•
•
•
Refer service or repairs, other than those described in the
operating instructions, to a professional service person.
This product is designed, tested, and approved to meet strict
global safety standards with the use of specific Lexmark
components. The safety features of some parts may not
always be obvious. Lexmark is not responsible for the use of
other replacement parts.
The Lexmark E234, Machine Type 4505-420 and Lexmark E234n,
Machine Type 4505-410, have been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
The FCC Class B limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
•
•
Your product uses a laser.
CAUTION: Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
Your product uses a printing process that heats the print
media, and the heat may cause the media to release
emissions. You must understand the section in your
operating instructions that discusses the guidelines for
selecting print media to avoid the possibility of harmful
emissions.
•
Reorient or relocate the receiving antenna.
Notices
7
•
•
•
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult your point of purchase or service representative for
additional suggestions.
Korean MIC statement
If your product includes the following
symbol on the regulatory label:
the following statement is applicable to
your product.
The manufacturer is not responsible for any radio or television
interference caused by using other than recommended cables or by
unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user's
authority to operate this equipment.
This equipment has undergone EMC registration as a household
product. It can be used in any area, including a residential area.
Note: To assure compliance with FCC regulations on
electromagnetic interference for a Class B computing device, use a
properly shielded and grounded cable such as Lexmark part
number 1329605 for parallel attach or 12A2405 for USB attach.
Use of a substitute cable not properly shielded and grounded may
result in a violation of FCC regulations.
Noise emission levels
The following measurements were made in accordance with
ISO 7779 and reported in conformance with ISO 9296.
Any questions regarding this compliance information statement
should be directed to:
1-meter average sound pressure, dBA
51—Machine types 4505-100, 4505-200, 4546-xxx
Director of Lexmark Technology & Services
Lexmark International, Inc.
740 West New Circle Road
Printing
Idling
52—Machine types 4505-300, 4505-310, 4547-xxx
30
Lexington, KY 40550
(859) 232-3000
ENERGY STAR
Industry Canada compliance statement
The EPA ENERGY STAR Office
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Equipment program is a partnership effort
with office equipment manufacturers to
promote the introduction of
energy-efficient products and to reduce air
pollution caused by power generation.
Avis de conformité aux normes de l’industrie du
Canada
Companies participating in this program introduce products that
power down when they are not being used. This feature will cut the
energy used by up to 50 percent. Lexmark is proud to be a
participant in this program.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du Canada.
European Community (EC) directives conformity
As an ENERGY STAR Partner, Lexmark International, Inc. has
determined that this product meets the ENERGY STAR guidelines
for energy efficiency.
This product is in conformity with the protection requirements of EC
Council directives 89/336/EEC and 73/23/EEC on the
approximation and harmonization of the laws of the Member States
relating to electromagnetic compatibility and safety of electrical
equipment designed for use within certain voltage limits.
A declaration of conformity with the requirements of the directives
has been signed by the Director of Manufacturing and Technical
Support, Lexmark International, S.A., Boigny, France.
This product satisfies the Class B limits of EN 55022 and safety
requirements of EN 60950.
Japanese VCCI notice
Notices
8
Printer energy consumption
Statement of Limited Warranty
The following table documents the power consumption
characteristics of the printer.
Lexmark International, Inc., Lexington, KY
This warranty applies to the United States and Canada. For
customers outside the U.S. and Canada, refer to the
Power consumption
(by Machine Type)
country-specific warranty information that came with your printer.
Lexmark E234, E234n
Mode
Description
4505-400
This Statement of Limited Warranty applies to this product if it was
originally purchased for your use, and not for resale, from Lexmark
or a Lexmark remarketer, referred to in this statement as
“Remarketer.”
Printer is generating
hard copy output
Printing
420 W
80 W
7 W
Printer is waiting for a
print job
Ready
Warranty
Power
Saver
Printer is in energy
saving mode
Lexmark warrants that this product:
Printer is plugged into a
wall outlet, but switch is
turned off
•
Is manufactured from new parts, or new and serviceable
used parts, which perform like new parts
Is free from defects in material and workmanship
Conforms to Lexmark’s official published specifications
Is in good working order
Off
0 W
•
•
•
The power consumption levels listed in the previous table represent
time-averaged measurements. Instantaneous power draws may be
substantially higher than the average.
If this product does not function as warranted during the warranty
period, contact a Remarketer or Lexmark for repair without charge.
If this product is a feature or option, this statement applies only
when that feature or option is used with the product for which it was
designed. To obtain warranty service, you may be required to
present the feature or option with the product.
Power Saver
As part of the ENERGY STAR program, this printer is designed with
an energy-saving mode called Power Saver. The Power Saver
Mode is equivalent to the EPA Sleep Mode. The Power Saver Mode
saves energy by lowering power consumption during extended
periods of inactivity. The Power Saver Mode is automatically
engaged after this printer is not used for a specified period of time,
called the Power Saver Timeout. The factory default Power Saver
Timeout is 30 minutes for the Lexmark E234 and Lexmark E234n.
By using the printer configuration menus, the Power Saver Timeout
can be modified between 1 minute and 240 minutes. Setting the
Power Saver Timeout to a low value reduces energy consumption,
but may increase the response time of the printer. Setting the Power
Saver Timeout to a high value maintains a fast response, but uses
more energy.
If you transfer this product to another user, warranty service under
the terms of this statement is available to that user for the
remainder of the warranty period. You should transfer proof of
original purchase and this statement to that user.
Warranty service
The warranty period is 12 months and starts on the date of original
purchase as shown on the purchase receipt.
To obtain warranty service you may be required to present proof of
original purchase. Warranty service will be provided at a
Remarketer or a Lexmark designated location. You may be required
to deliver your product to the Remarketer or Lexmark, or ship it
prepaid and suitably packaged to a Lexmark designated location.
You are responsible for loss of, or damage to, a product in transit to
the Remarketer or the designated location.
When warranty service involves the exchange of a product or part,
the item replaced becomes the property of the Remarketer or
Lexmark. The replacement may be a new or repaired item. The
replacement item assumes the remaining warranty period of the
original product.
Replacement is not available to you if the product you present for
exchange is defaced, altered, in need of a repair not included in
warranty service, or damaged beyond repair. Also, such product
must be free of any legal obligation or restrictions that prevent its
exchange.
If the Power Saver Mode is affecting the effective use of this printer,
this mode can be disabled from the Local Printer Setup Utility (see
page 99) or, if you have a network model, from the printer’s resident
Web page (see page 98).
Total energy usage
It is sometimes helpful to calculate the total printer energy usage.
Since power consumption claims are provided in power units of
Watts, the power consumption should be multiplied by the time the
printer spends in each mode in order to calculate energy usage.
The total printer energy usage is the sum of each mode's energy
usage.
Before you present this product for warranty service, remove all
programs, data, and removable storage media.
Notices
9
For further explanation of your warranty alternatives and the
nearest Lexmark authorized servicer in your area, please contact
Lexmark at 1-859-232-3000, or on the World Wide Web at http://
support.lexmark.com.
Remote technical support is provided for this product throughout its
warranty period. Lexmark offers a variety of extended warranty
programs that include an extension of technical support. For
products no longer covered by a Lexmark warranty, technical
support may only be available for a fee.
Additional rights
Some states do not allow limitations on how long an implied
warranty lasts, or do not allow the exclusion or limitation of
incidental or consequential damages. If such laws apply, the
limitations or exclusions contained in this statement may not apply
to you.
This warranty gives you specific legal rights. You may also have
other rights which vary from state to state.
Extent of warranty
We do not warrant uninterrupted or error-free operation of a
product.
Warranty service does not include repair of failures caused by:
•
•
•
•
Modification or attachments
Accidents or misuse
Unsuitable physical or operating environment
Maintenance by anyone other than Lexmark or a Lexmark
authorized servicer
•
•
Operation of a product beyond the limit of its duty cycle
Failure to have installed a maintenance kit as specified (if
applicable)
•
•
Use of printing media outside of Lexmark specifications
Use of other than Lexmark supplies (such as toner
cartridges, inkjet cartridges, and ribbons)
Use of other than Lexmark product or component
•
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION
TO THE WARRANTY PERIOD. NO WARRANTIES, EXPRESS
OR IMPLIED, WILL APPLY AFTER THIS PERIOD.
Limitation of liability
Your sole remedy under this Statement of Limited Warranty is set
forth in this section. For any claim concerning performance or
nonperformance of Lexmark or a Remarketer for this product under
this Statement of Limited Warranty, you may recover actual
damages up to the limit set forth in the following paragraph.
Lexmark's liability for actual damages from any cause whatsoever
will be limited to the greater of 1) $5,000 or 2) the amount you paid
for the product that caused the damages. This limitation of liability
will not apply to claims by you for bodily injury or damage to real
property or tangible personal property for which Lexmark is legally
liable. In no event will Lexmark be liable for any lost profits, lost
savings, incidental damage, or other economic consequential
damages. This is true even if you advise Lexmark or a Remarketer
of the possibility of such damages. Lexmark is not liable for any
claim by you based on a third party claim.
This limitation of remedies also applies to any developer of
materials supplied to Lexmark. Lexmark’s and the developer’s
limitations of remedies are not cumulative. Such developer is an
intended beneficiary of this limitation.
Notices
10
|