Owner’s Manual
SRCOOL12K (120V, 60 Hz)
SRXCOOL12K (230V, 50 Hz)
Portable Air Conditioning Unit
Introduction
2
2
Important Safety Instructions
Features
3
Installation
4
Operation
6
General Maintenance
Troubleshooting
Storage & Service
Warranty & Warranty Registration
Español
7
8
8
8
9
Français
17
1111 W. 35th Street, Chicago, IL 60609 USA
Copyright © 2009 Tripp Lite. All rights reserved.
Features
Front View
I
A
B
C
D
E
F
G
H
I
Control Panel
A
Recessed Handle
Air Filter Covers
Drainage Outlet
Casters
B
H
G
Front Panel
Main Air Outlet
Standard, Louvered Air Vent
Ducted Cooling Vent
C
F
J
L
D
E
Rear View
J
K
L
Recessed Handles
Rear Panel
Warm Air Exhaust Vent
K
Control Panel
M
O
N
M
N
O
P
ON/OFF Button
MODE Button
TEMPERATURE CONTROL Buttons
POWER LED
X
P
Q
R
W
Q
R
S
DISPLAY LCD
LOCK LED
FAN SPEED Button
TIMER Button
V
U
T
S
T
U
V
LOCK Button
FAN SPEED LEDs
TIMER LED
W
X
MODE-FUNCTION LEDs
3
Installation
Upon removing the air conditioning unit from the box, check for any signs of shipping damage or missing parts (refer to parts list on page 2). If
Select a Proper Location
Install your portable air conditioner on a flat, level surface with rear and vented sides not less
than 20 inches (50 cm) from walls or other obstacles (see diagram). Be sure to install the unit
close to a properly grounded outlet. Also be sure the unit is placed near enough to a window,
or in a convenient spot for Window/Drop Ceiling installation. Wall outlet should have a power
supply consistent with that of the printed tag on the air conditioning unit, 90-110% of its rated
voltage.
More than 20”
(50 cm)
Note: Do not use an extension cord to plug in the unit. This appliance should be installed in
accordance with national and local wiring regulations.
More than 20”
(50 cm)
WALL
Installing Standard, Louvered
Air/Ducted Cooling Vents
To remove, hold the upper portion of the
selected vent (Standard, Louvered Air Vent for
room cooling, Ducted Cooling Vent for ducted
cooling), pull it outwards and upwards toward
you. To install or replace, position the vent
into the slot, and snap it down into place.
Exhaust/Cooling Duct
Mounting Instructions
Affix one end of the duct (longer tube) to
the Warm Air Exhaust Vent on the back
panel of the unit. Pushing inward, turn the
duct clockwise into the outlet as seen in the
diagram, being sure the duct is connected
solidly. Connect the Duct Adapter to the other
side of the duct in the same manner. You are
now ready for Window/Drop Ceiling Kit
installation described in the next section.
For Ducted Cooling
Attach Ducted Cooling Vent to the unit’s
Main Air Outlet. Affix one end of the duct
(shorter tube) to the Ducted Cooling Vent
by pushing downwards and turning the duct
clockwise into the vent as seen in the diagram,
being sure the duct is connected solidly. The
other end of the duct can now be placed in
a specific location for isolated cooling, such
as in a wiring closet or attached to a rack
configuration.
4
Installation
Window Kit Installation
Your portable air conditioner’s Window/Drop Ceiling Kit has been designed to fit most standard
vertical and horizontal window applications. It may be necessary to modify some aspects of the
installation process for certain types of windows. In both typical and modified installations, the
user must determine the fitness of hardware and procedures before mounting. The procedures
described in this manual are for common window types and may not be appropriate for all
applications.
Figure A
Figure B
Nut
Bolt
The Window/Drop Ceiling Kit’s Adapter Board can accommodate a minimum window opening
of 26.57 inches (67.5 cm) and a maximum of 49.21 inches (125 cm).
Horizontal Window
1. Measure your window’s opening and adjust the Adapter Board accordingly. When the correct
measurement is determined, lock the board in place using the supplied nut and bolt (see
Figure A).
2. Attach the Exhaust/Cooling Duct with the Duct Adapter into the oblong hole in the Window/
Drop Ceiling Kit’s Adapter Board. The adapter will snap into place.
Window slide kit
minimum: 26.57 in. (67.5 cm)
maximum: 49.21 in. (125 cm)
3. Insert the Window/Drop Ceiling Kit’s Adapter Board into your window’s opening as seen in
Figure B or C. Vertical or horizontal mounting will depend on your application.
4. Simply close the window appropriately, providing a tight seal against the Window Kit’s
Adapter Board. A tight seal will ensure the unit’s efficiency.
Figure C
Vertical
Window
Window slide kit
minimum: 26.57 in. (67.5 cm)
maximum: 49.21 in. (125 cm)
Drop Ceiling Installation
It may be necessary to modify some aspects of the installation process for certain types of
ceilings. In both typical and modified installations, the user must determine the fitness of
hardware and procedures before installing. The procedures described in this manual may not be
appropriate for all applications.
1. Measure the dimensions of your ceiling grid and adjust the Adapter Board accordingly. The
Adapter Board should measure slightly longer than the spacing in the grid so that it may rest
directly on top of the grid panels. When the correct measurement is determined, lock the
board in place using the supplied nut and bolt (see Figure A.)
2. Attach the Exhaust/Cooling Duct with the Duct Adapter into the oblong hole in the Window/
Drop Ceiling Kit’s Adapter Board. The adapter will snap into place.
3. Slide your ceiling tile out of the way and place the Adapter Board inside the ceiling space, on
top of the grid panels as seen in the diagram. Note: There should be at least 10 to 15 inches of
space above the Exhaust/Cooling Duct so that the duct is not blocked.
Install sliding
board above
ceiling grid
Slide ceiling tile
4. Slide your ceiling tile back into place as far as it will go. Be sure to slide the tile back as far
as it can go to ensure the unit’s efficiency.
Note: The Exhaust Duct (longer tube) can be stretched to a maximum length of 118 inches (300
cm). It is better to keep the duct’s length to a minimum. Excessive stretching or bending of the
duct will affect cooling efficiency.
INCORRECT
CORRECT
5
Operation
Before beginning operating procedures, be sure your air conditioning unit is properly plugged into an appropriately grounded outlet and the
Exhaust/Cooling Duct is properly installed for you application.
Note: Do not use an extension cord to plug in your unit.
Power
Turn the SRCOOL12K/SRXCOOL12K on or off by pressing the ON/OFF Button.
Cool
Activate the Cool Mode by pressing the MODE Button. Pressing the MODE Button will
sequentially cycle between Cooling, Dehumidifying and Fan Modes. You will know you have
reached Cool Mode when the COOL LED illuminates.
To set the temperature in Cool Mode, press the TEMP+ and TEMP- Buttons. The temperature
selected will display in the Display LCD.
To set the fan speed in Cool Mode, press the FAN SPEED Button. Pressing the FAN SPEED
Button will sequentially cycle between High, Medium and Low. You will know which speed
you have reached when the appropriate LED illuminates.
Dehumidify
Activate the Dehumidify Mode by pressing the MODE Button. As it cycles through modes, you
will know when you have reached Dehumidify Mode when the DRY LED illuminates. In this
mode, the fan will run at a fixed speed and temperature controls become irrelevant. Be sure to
close all windows and doors for optimal performance in this mode.
Fan
Activate the Fan Mode by pressing the MODE Button. As it cycles through modes, you will
know when you have reached Fan Mode when the FAN LED illuminates.
To set the fan speed in Fan Mode, press the FAN SPEED Button. Pressing the FAN SPEED
Button will sequentially cycle between High, Medium and Low. You will know which speed
you have reached when the appropriate LED illuminates.
Timer
The TIMER Button allows you to set an automatic turn-on or shut-off function in a number of
hours preset by the user. TIMER Mode will be indicated by the TIMER LED illuminating.
Timer On
Note: Unit must be OFF to activate the Timer On fuction.
Activate the timer by pressing the TIMER Button. Press the TEMP+ and - Buttons to set the
time (in hours) that you want the unit to turn on. The number of hours will display in the
Display LCD. Press the TIMER Button again to confirm your time. Be sure that your Mode,
Temperature and Fan Speed settings are all correct before accessing the Timer On function.
Timer Off
Note: Unit must be ON to activate the Timer Off function.
Activate the timer by pressing the TIMER Button. Press the TEMP+ and - Buttons to set the
time (in hours) that you want the unit to turn off. The number of hours will display in the
Display LCD. Press the TIMER Button again to confirm your time.
System Lock
Activate a System Lock function by pressing the LOCK Button. You will also see the LOCK
LED illuminate. During a System Lock, all function buttons will be disabled, so as not to
disturb settings. To Unlock, simply press the LOCK Button again.
6
Operation
Dealing with Condensation
Over time, condensation will form when the SRCOOL12K/SRXCOOL12K is in Cool or
Dehumidify Modes. This unit offers a built-in evaporator that takes this condensation and re-
evaporates it back into the hot exhaust stream. The unit contains no user-removable tank that
requires emptying.
A Drainage Outlet on the side of the unit exists for those wanting a dedicated drainage system
instead of re-evaporation. Simply connect a draining tube to the Drainage Outlet and run the
tube to your facility’s drainage receptacle.
For those opting to use a dedicated drainage system, if the drainage system becomes clogged,
there is a small internal reservoir that will collect the water until the system is cleared. If not
cleared in time or if the reservoir fills, the unit will automatically shut down.
Drainage Outlet
Before implementing a dedicated drainage system, be sure the power is
off and the unit is unplugged! Failure to heed this warning may result in
electrical shock!
General Maintenance
The SRCOOL12K/SRXCOOL12K has been designed to give you many years of dependable service. It is important, however, to care for the unit
and practice routine maintenance procedures to insure proper and efficient functioning.
Cleaning the Air Filters
It is important to keep the air filters clean and free of dust. When the filters become dirty or covered in dust, it decreases the cooling effect and can
threaten air quality. Tripp Lite recommends cleaning the filters at least once every two weeks.
Before cleaning the air filters, turn the unit off and be sure it is unplugged! Failure to heed this warning may result in
electrical shock or other personal injury!
1. Slide out the Air Filter Covers as seen in the diagram.
2. Remove the air filters and wash it in warm water with a neutral detergent. DO NOT put
the filters into a dishwasher or use harsh detergents or chemicals. Let the filters air dry
completely. Note: DO NOT use hot water over 104°F (40°C) to clean the filters.
3. Replace the filters and slide the Air Filter Covers back into their original position. You are
now ready to replace the unit to its original location and resume normal use.
Cleaning the Cabinet
It is recommended that the cabinet be cleaned periodically to avoid excess dust build up.
Before cleaning the cabinet, turn the unit off and be sure it is unplugged!
Failure to heed this warning may result in electrical shock or other
personal injury!
1. Wipe down the unit with a dry, non-abrasive cloth. Do not use gasoline, benzene, thinners
or other harsh chemicals as this can seriously damage the surface. Never pour water directly
over the unit or into the working parts. This will cause deterioration of electrical components,
wiring insulation and poses a threat of electrical shock.
2. In extreme cases, wipe down the unit with a damp cloth to remove residue.
7
Troubleshooting
To save time on service calls, please try the following suggestions if your unit does not appear to work properly. For any problems not covered, or
Problem
Possible Cause
Solution
Unit does not start.
• Power is not on.
• Turn on the power.
• Unit is not plugged in.
• Main power is off.
• Condensate tank is full.
• Plug unit into the wall.
• Check fuses or circuit breaker.
• Drain the unit.
Poor cooling performance.
• Air exhaust or intake is blocked.
• Check that all ducts and intake valves are
clear of obstructions.
• Temperature set too high/low.
• Fan speed set too high/low.
• Dirty air filter.
• Adjust temperature setting.
• Adjust fan setting.
• Clean the filter.
Unit leaks water.
• Drainage valve is open.
• Un-level surface.
• Close drainage valve.
Excessive noise or vibration.
• Move unit to a level, stable surface.
Storage and Service
Storage
Before storing the unit for any considerable length of time, be sure that the Exhaust Duct and all vents are secured or removed and cared for
properly. Also be sure to drain the unit of condensation before storing.
Service
Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended Warranty and On-Site Service Programs
follow these steps:
1. Review the installation and operation procedures in this manual to insure that the service problem does not originate from a misreading of the
instructions.
Material Authorization (RMA) number, which is required for service. This simple on-line form will ask for your unit’s model and serial
numbers, along with other general purchaser information. The RMA number, along with shipping instructions will be emailed to you. Any
damages (direct, indirect, special or consequential) to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service
center is not covered under warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges
prepaid. Mark the RMA number on the outside of the package. If the product is within its warranty period, enclose a copy of your sales receipt.
Return the product for service using an insured carrier to the address given to you when you request the RMA.
Warranty
1-YEAR LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 1 year from the date of initial purchase. If the product
should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this Warranty can only be obtained by your delivering or shipping the
product (with all shipping or delivery charges prepaid) to: Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; USA. Seller will pay return shipping charges.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER
THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction).
Tripp Lite; 1111 W. 35th Street; Chicago IL 60609; USA
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the
manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with
all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model
number of the product.
Tripp Lite follows a policy of continuous improvement. Product specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA
200907001 • 932918-EN
8
|