ONE YEAR LIMITED WARRANTY
SI PRODUCTS sells its products with the intent that they are free of defects in manufacture and
workmanship for the life of the original purchaser from the date of original purchase, except as noted
below. SI PRODUCTS warrants that its products will be free of defects in material and workmanship
under normal use and service. This warranty extends only to consumers and does not extend to
Retailers.
To obtain warranty service on your SI PRODUCTS product, mail the product and your dated sales
receipt (as proof of purchase), postpaid, to the following address:
SI PRODUCTS Consumer Relations
Service Center Dept. 168
3000 Pontiac Trail
®
Sound Soother
20 Soothing Sounds
Commerce Township, MI 48390
No COD's will be accepted.
SI Products
Service Center
SI PRODUCTS does not authorize anyone, including, but not limited to, Retailers, the subsequent
consumer purchaser of the product from a Retailer or remote purchasers, to obligate SI PRODUCTS
in any way beyond the terms set forth herein. This warranty does not cover damage caused by
misuse or abuse; accident; the attachment of any unauthorized accessory; alteration to the product;
improper installation; unauthorized repairs or modifications; improper use of electrical/power supply;
loss of power; dropped product; malfunction or damage of an operating part from failure to provide
manufacturer’s recommended maintenance; transportation damage; theft; neglect; vandalism; or
environmental conditions; loss of use during the period the product is at a repair facility or otherwise
awaiting parts or repair; or any other conditions whatsoever that are beyond the control of SI
PRODUCTS.
This warranty is effective only if the product is purchased and operated in the country in which the
product is purchased. A product that requires modifications or adoption to enable it to operate in any
other country than the country for which it was designed, manufactured, approved and/or authorized,
or repair of products damaged by these modifications is not covered under this warranty.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE
SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS OR ANY OTHER OBLIGATION ON THE PART OF THE COMPANY WITH
RESPECT TO PRODUCTS COVERED BY THIS WARRANTY. SI PRODUCTS SHALL HAVE NO LIABILITY FOR
ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. IN NO EVENT SHALL THIS WARRANTY
REQUIRE MORE THAN THE REPAIR OR REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO
BE DEFECTIVE WITHIN THE EFFECTIVE PERIOD OF THE WARRANTY.
1.888.856.6781
8:30a.m. – 7:00p.m. (EST)
M – F
Mail To: SI Products
Consumer Relations
Service Center Dept. 168
3000 Pontiac Trail
Commerce Township, MI
48390
e-mail:
NO REFUNDS WILL BE GIVEN. IF REPLACEMENT PARTS FOR DEFECTIVE MATERIALS ARE NOT
AVAILABLE, SI PRODUCTS RESERVES THE RIGHT TO MAKE PRODUCT SUBSTITUTIONS IN LIEU OF
REPAIR OR REPLACEMENT.
This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed
products, including but not limited to sale of such products on Internet auction sites and/or sales of
such products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately
cease and terminate as to any products or parts thereof which are repaired, replaced, altered, or
modified, without the prior express and written consent of SI PRODUCTS.
This warranty provides you with specific legal rights. You may have additional rights which may vary
from state to state. Because of individual regulations, some of the above limitations and exclusions
may not apply to you.
For service or repair - do not return this unit to the retailer.
Contact SI PRODUCTS Consumer Relations at 1-888-856-6781.
©The Sharper Image. All rights reserved. THE SHARPER IMAGE name and logo are registered
trademarks.
Instruction Manual and
Warranty Information
EC-B100
©2009 THE SHARPER IMAGE and its affiliated companies, all rights reserved. THE SHARPER IMAGE is a
registered trademark of THE SHARPER IMAGE and its affiliated companies. All rights reserved.
IB-ECB100
Sound Soother® Features:
•
20 Digitally Recorded Sounds: Aviary, Brook, City, Dockside, Ebb Tide,
Everglades, Fireside, Foghorns, Heartbeat, North Woods, Oceanside, Rain,
Rainforest, Roadside, Steam Train, Summer Night, Surfs Up, Thunderstorm,
White Noise, Wind Chimes.
•
•
•
•
•
•
•
Easy-to-read illuminated LCD with white backlight displays time & sound name
Dual Alarm Clock for individual wake times
Choice of two Alarm Wake Modes: Soothing Sounds or Beep Tone
Snooze automatically set for nine minutes for extended sleep
Digital volume control adjusts the volume of your sound selection
2-pc speaker included (2.5” in diameter)
Powered by 3V DC (a total of 3 (three) AA batteries (not included)) or 6V
300mA (120V input ) AC/DC adaptor (included)
Battery installation:
Alarm clock uses an AC adaptor (included) or 3 (three) AA batteries
(not included).
The battery power is designed only to provide MEMORY BACK-UP for the clock
and alarm settings. Three AA batteries (not included) should be inserted following
the polarity marked in the battery compartment if memory back-up is desired (in
the event of power outages or if the unit is unplugged). However, the time will
not be illuminated on the clock display. As soon as the power supply returns, the
display will indicate the correct time.
NOTE: Battery must be installed in order for clock memory back-up to operate.
In the event of a power failure or disconnection, if the battery is not installed, the
clock and alarm will need to be re-set when power is restored.
Fig. 1
5
4
Choosing the Sound Selection:
Battery Precautions
1. Press the POWER button.
•
•
Use only the size and type of batteries specified.
2. Press the right side of the MUSICAL NOTE “>” button for the next nature
sound (short press). Long press and hold to fast forward.
3. Press the left side of the MUSICAL NOTE “<” button for previous nature sound
(short press). Long press and hold to go backwards quickly.
(Refer to Fig.2)
When installing batteries, observe proper +/- polarities. Incorrect installation of
battery may cause damage to the unit.
•
•
•
Do not mix different types of batteries together (e.g., alkaline with carbon-zinc
or old batteries with new ones).
If the unit is not going to be used for a long period of time, remove batteries to
prevent damage due to possible battery leakage.
NOTE: The digital display should show the sound number with the respective
Do not dispose of batteries in fire. Batteries may explode or leak.
sound name.
POWER:
Volume Control:
Plug adapter into a 120V AC outlet and plug the receptacle end into the input jack
on the back of the unit. Press the POWER button (located center of top panel) to
turn the sound on or off.
•
•
Press “+” to increase the volume level.
Press “-“ to decrease the volume level.
Setting the Clock:
1. Long press and hold the DATE/TIME SET button (for more than 3 seconds)
and press “+” and “-“ to “INCREASE” (+) and “DECREASE” (-) to the time you
desire. Press it again once to set Year > Month > Day > Hour > Minute > Exit.
NOTE: AM/PM choice will be made at this time.
2. Short press DATE/TIME SET button once, it will display the date. Press twice,
it will display the time. Normal time display will return after 5 seconds.
(Refer to Fig.2)
Fig. 2
6
7
al 2 Button
Setting and Using the Alarm:
For your convenience, two separate alarms may be set to accompany individual
wake-up times.
Short press the al2 button: Set Alarm mode, Beep, Sound, Off
The alarm 2 bell icon will appear next to the selected mode when alarm is set.
Press and hold the al 2 button:
1. The “ALARM 2” icon illuminates, time flashes for hour (HH), press “-/+“
button to change hour setting.
•
•
al 1 = “Alarm 1”
al 2 = “Alarm 2”
(Refer to Fig.2)
2. Press Alarm 2 button to confirm and change to minute setting. Time
flashing for minutes (MM), press “-/+“ button to change Minute setting, wait
for timeout to save and go back to normal mode.
3. The digital display will then show “ALARM 2” icon after you have
successfully set the ALARM 2 time.
al 1 Button
Short press al 1 button: Set Alarm mode, Beep, Sound, Off
The Alarm 1 bell icon will appear next to the selected mode when alarm is set.
Press and hold the al 1 button:
1. The “ALARM 1” icon illuminates, time flashes for hour (HH), press “-/+“ button
to change HOUR setting.
Snooze:
2. Press Alarm 1 button to confirm and change to the minute setting. Time
flashes for minutes (MM), press “-/+“ button to change MINUTE setting, wait
for timeout to save and go back to normal mode.
3. The digital display will then show “ALARM 1” icon after you have successfully
set the ALARM 1 time.
When the alarm sounds, press the SNOOZE/TIMER button to snooze. This will
automatically activate snooze time for nine minutes. Press the POWER button
to turn snooze off.
Timer:
When the power is on and you are listening to a nature sound, you may set a
timer so the unit will automatically turn off.
1. Toggle through the SNOOZE/TIMER button until you find the time of your
choice, 15, 30, 45 or 60 minutes.
2. To cancel the timer, toggle through the SNOOZE/TIMER button until the
LED light says “OFF” or press POWER.
(Refer to Fig.2)
9
8
•
•
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Settings located on back:
DC IN:
DC Jack for adaptor plug-in.
•
Consult the dealer or an experienced radio/TV technician for help.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO
OPERATE THE EQUIPMENT.
Daylight Savings Time:
Slide the DST ON/OFF button to activate or inactivate the Daylight Savings Time
feature, which will automatically adjust for Daylight Savings Time.
BACKLIGHT:
Choose between three settings of brightness on your display: HI, MED or LO.
Maintenance
To Store
You may leave the unit on display, or you can store it in its box in a
cool, dry place.
To Clean
Use only a soft dry cloth to clean the enclosure of the unit.
NEVER use liquids or abrasive cleaner to clean.
Modifications not authorized by the manufacturer may void user warranty.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
11
10
|