Toshiba Camera Accessories IK HD1D User Manual

CAMERA CONTROL UNIT  
INSTRUCTION MANUAL  
IK-HD1D  
For Customer Use  
Enter below the Serial #  
which is located on the  
bottom of the cabinet. Retain  
this information for future ref-  
erence.  
Model #  
Serial #  
IK-HD1D  
FCC NOTICE  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-  
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
USER-INSTALLER CAUTION:Your authority to operate this FCC verified equipment could be voided if  
you make changes or modifications not expressly approved by the party responsible for compliance to  
Part 15 of the FCC Rules.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.  
Following information is only for EU-member states:  
The use of the symbol indicates that this product may not be treated as household waste.  
By ensuring this product is disposed of correctly, you will help prevent potential negative  
consequences for the environment and human health, which could otherwise be caused by  
inappropriate waste handling of this product. For more detailed information about the take-  
back and recycling of this product, please contact your supplier where you purchased the  
product or consult.  
This manual is made from recycled paper.  
 
Note the following instructions when installing.  
• Do not cover the product with any material.  
• Do not place the product on any inflammable material such as a carpet or  
blanket.  
• Do not place the product in a confined space, as this may cause heat to  
build up inside the product.  
Failure to follow the above cautions may result in fire.  
Do not place the product in direct sunshine and/or high temperature.  
Temperature build up inside the product may result in fire.  
Avoid placing in humid, smoky, or dusty places.  
This may result in fire and/or electrical shock.  
Ask your dealer to perform a periodical check and internal cleaning (approx.  
once every five years).  
Dust inside the product may result in fire. For check and cleaning cost, please  
consult your dealer.  
The following description is for that a camera head “IK-HD1H” connected to this camera control unit.  
Do not point the lens directly at the sun and/or intensive light such as di-  
rect sunlight, etc.  
Focusing of the light may result in eye injury and/or fire.  
Disclaimer  
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the  
user in any of the following cases:  
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-  
tional or accidental; use under extreme operating conditions.  
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including  
but not limited to loss of expected income and suspension of business activities.  
3. Incorrect use not in compliance with instructions in this instruction manual.  
4. Malfunctions resulting from misconnection to other equipment.  
5. Repairs or modifications made by the user or caused to be made by the user and carried out by  
an unauthorized third party.  
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the  
purchase price of the product.  
Copyright and Right of Portrait  
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,  
distributes, or exhibits an image picked up by the camera without permission from the copyright  
holder. Please also note that transfer of an image or file covered by copyright is restricted to use  
within the scope permitted by the Copyright Law.  
Protection of Personal Information  
Images taken by the camera that reveal the likeness of an individual person may be considered  
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,  
consent of the person may be required.  
3
 
Limitation of Usage  
The product is not designed for any “critical applications.Critical applications” means life support  
systems, exhaust or smoke extraction applications, medical applications, commercial aviation, mass  
transit applications, military applications, homeland security applications, nuclear facilities or systems  
or any other applications where product failure could lead to injury to persons or less of life or  
catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising out of  
the use of the product in any critical applications.  
TABLE OF CONTENTS  
1
2
3
4
5
CAUTIONS ON USE AND INSTALLATION ............................................ 6  
COMPONENTS ....................................................................................... 6  
ITEMS CONTROLLED BY THE ON SCREEN DISPLAY........................ 7  
NAMES AND FUNCTIONS...................................................................... 8  
CONNECTION........................................................................................  
9
9
5.1 Standard Connection ..................................................................................................  
5.2 Cautions on Connection.............................................................................................. 10  
5.3 Connection on Back Panel.......................................................................................... 10  
5.3A Connector Pin Assignments ..................................................................................... 10  
6
7
OPERATION........................................................................................... 11  
6.1 Automatic Black Balance ............................................................................................ 11  
6.2 White Balance............................................................................................................. 12  
6.3 Scene File................................................................................................................... 14  
6.4 Gain............................................................................................................................. 14  
6.5 Shading Correction ..................................................................................................... 15  
MODE SETTING BY THE ON SCREEN DISPLAY ................................ 16  
7.1 Using the Menus......................................................................................................... 16  
7.2 Menus ......................................................................................................................... 17  
(1) SHUTTER (Electronic shutter) .................................................................................... 17  
(1.1) Changing the setting in AUTO mode................................................................... 18  
(1.2) Changing the setting in MANUAL mode.............................................................. 20  
(1.3) Changing the setting in SS (Synchro. Scan) mode ............................................. 20  
(2) GAIN (Video gain) ....................................................................................................... 21  
(2.1) Changing maximum gain in AUTO (Automatic gain control) mode .................... 21  
(2.2) Changing gain in MANUAL mode........................................................................ 21  
(3) WHT BAL (White Balance).......................................................................................... 22  
(3.1) Changing the setting in AWB (Automatic White Balance) mode ........................ 22  
(3.2) Changing the setting in ATW (Automatic Tracking White balance) mode ......... 23  
(3.3) Changing gain in MANUAL mode ....................................................................... 24  
(4) PROCESS ................................................................................................................... 25  
(4.1) Changing gamma correction ON/OFF ................................................................ 25  
(4.2) Changing gamma correction level....................................................................... 25  
(4.3) Changing detail (outline) gain.............................................................................. 26  
(4.4) Changing master pedestal .................................................................................. 26  
(4.5) Changing DNR(Digital Noise Reduction)............................................................. 26  
(5) MATRIX(Matrix color correction)................................................................................. 27  
(5.1) Changing Matrix color correction ON/OFF .......................................................... 27  
(5.2) Changing MATRIX setting...............................................................................  
27  
4
 
(6) SYNC........................................................................................................................... 28  
(6.1) INT screen........................................................................................................... 28  
(6.2) Changing EXT. setting ........................................................................................ 28  
(7) OPTION....................................................................................................................... 29  
(7.1) Changing OUTPUT mode .................................................................................. 29  
(7.2) Changing shading correction mode .................................................................... 29  
(7.3) Changing manual shading correction mode ........................................................ 29  
(7.4) Changing RGB SYNC ......................................................................................... 30  
(7.5) Changing RS232C baud rate .............................................................................. 30  
(7.6) Changing OSD OUTPUT mode .......................................................................... 30  
(8) Returning to factory settings ....................................................................................... 30  
7.3 External Sync.............................................................................................................. 31  
(1) External sync signal input conditions........................................................................... 31  
(2) External sync frequency range.................................................................................... 31  
(3) Using the unit with external sync signal....................................................................... 31  
(3.1) H (Horizontal) phase adjustment ......................................................................... 31  
7.4 Synchro. Scan Operation............................................................................................ 31  
(1) Setting by 1H ............................................................................................................... 31  
8
9
BEFORE MAKING A SERVICE CALL.................................................... 32  
SPECIFICATIONS.................................................................................. 33  
10 EXTERNAL APPEARANCE DIAGRAM................................................ 34  
5
 
1. CAUTIONS ON USE AND INSTALLATION  
Handling the unit.  
The following descriptions are for the camera head  
"IK-HD1H" connected to this camera control unit.  
Do not drop, jolt, or vibrate, as this may result in  
damage to the unit. This may cause problems.  
Treat the camera cables carefully to prevent  
cable problems, such as breaks in the cable and  
loose connections.  
Do not shoot intense light.  
If there is an intense light at a location on the  
screen such as a spot light, a blooming and smear-  
ing may occur. When intense light enters, vertical  
stripes may appear on the screen. This is not a  
malfunction. Ghosts may occur when there is an  
intense light near the object. In this case, change  
the shooting angle.  
Install the camera in a location free from noise.  
If the camera or the cables are located near power  
utility lines or a TV, etc. undesirable noise may ap-  
pear on the screen. In such a case, try to change  
the location of the camera or the cable wiring.  
Moire  
A moire pattern is an interference pattern  
generated when two repetitive line patterns  
overlap. This is not a malfunction. Eliminating the  
repetitive line patterns, or aligning the two  
patterns, will eliminate the moire.  
Operating ambient temperature and humidity.  
Do not use the camera in places where tempera-  
ture and humidity exceed the specifications. Pic-  
ture quality will deteriolate and internal parts may  
be damaged.  
Handling of the camera head and protection  
cap.  
Be particularly careful when using in places ex-  
posed to direct sunlight. When shooting in hot  
places, depending on the conditions of the object  
and the camera (for example when the gain is in-  
creased), noise in the form of vertical stripes or  
white dots may occur. This is not a malfunction.  
Keep the camera head and protection cap away  
from children, as they may pose a choking  
hazard. The protection cap protects the image  
sensing plane when the lens is removed from the  
camera head, do not discard.  
When not using the camera for extended  
periods of time.  
When cleaning the camera.  
Switch the control unit off and disconnect the  
power supply.  
Unplug the power source before cleaning. Clean  
with a soft dry cloth only. Do not use chemicals or  
chemically treated cloths. Chemicals may damage  
coatings and printed letters. When cleaning the  
lens, use lens cleaning paper.  
Avoid using or storing the camera in the fol-  
lowing places:  
Places filled with highly flammable gas.  
Places near gasoline, benzene, or paint thinner.  
Places subject to strong vibration.  
Installation without a tripod.  
Before installing the camera head, make sure  
that the location can withstand the total weight of  
the camera head.  
Places containing chemicals (such as pesticides),  
rubber or vinyl products for extended periods of  
time.  
If this is not the case, reinforce the area to  
prevent the unit from dropping, which may result  
in damage to the unit or personal injury.  
2. COMPONENTS  
1
2
Camera Control Unit ............................................................................................... 1  
Accessories  
Instruction manual ........................................................................................ 1  
a
6
 
3
ITEMS CONTROLLED BY THE ON SCREEN DISPLAY  
Preset value  
(Factory setting)  
MANUAL  
Item  
Available selections  
AUTO, MANUAL, SS  
MODE  
-100  
0
100  
AUTO level  
0
00 10  
05 05  
10 00  
05 05  
10  
PRESET A  
AUTO peak/average  
AUTO response speed  
AUTO area  
1
10 20  
PRESET A, PRESET B, PRESET C,  
PRESET D, PRESET E  
OFF  
MANUAL speed  
OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,  
1/3000s, 1/5000s, 1/10000s, 1/30000s, 1/50000s  
OFF, 1/1125H 560/1125H  
AUTO, MANUAL, OFF  
Syncro. scan  
MODE  
OFF  
OFF  
AUTO maximum gain  
MANUAL gain  
MODE  
Color temperature  
AWB R PAINT  
AWB B PAINT  
AWB area  
0dB to 18dB  
0dB to 18dB  
AWB, ATW, MANUAL  
3200K, 5600K  
18dB  
0dB  
AWB  
3200K  
0
-10  
-10  
0
0
10  
10  
0
PRESET A, PRESET B, PRESET C,  
PRESET D, PRESET E  
PRESET A  
-10  
-10  
0
0
10  
10  
ATW R PAINT  
ATW B PAINT  
0
0
-100  
-100  
0
0
100  
100  
MANUAL R GAIN  
MANUAL B GAIN  
0
0
Gamma correction  
Gamma correction level  
Detail gain  
ON, OFF  
-10  
ON  
0
0
0
10  
-7(OFF)  
-100  
0
7
0
100  
Master pedestal  
0
Digital noise reduction(DNR) ON, OFF  
OFF  
ON  
0
0
0
0
0
0
0
0
0
0
0
Correction ON/OFF  
R hue  
R gain  
G hue  
G gain  
B hue  
B gain  
Ye hue  
Ye gain  
Cy hue  
Cy gain  
Mg hue  
Mg gain  
ON, OFF  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-15  
-650  
0
0
0
0
0
0
0
0
0
0
0
0
15  
15  
15  
15  
15  
15  
15  
15  
15  
15  
15  
15  
650  
0
0
Ext. Sync H phase adjustment  
OUTPUT  
Shading correction mode  
Manual shading correction  
RGB SYNC  
0
Y/Pb /Pr  
OFF  
0
G
Y/Pb /Pr , RGB  
SET, MANUAL, OFF  
-128 127  
0
G, ALL ON, ALL OFF  
9600bps, 19200bps  
ALL ON, Analog, Digital  
RS232C baud rate  
OSD OUTPUT  
9600bps  
ALL ON  
7
 
4. NAMES AND FUNCTIONS  
FILE button  
DISP button  
POWER switch  
MENU UP  
(SHD) button  
POWER LED  
DATA UP  
(AWB) button  
Camera cable  
for “IK-HD1H”  
terminal  
DATA DOWN  
(ABB) button  
GAIN button  
MENU DOWN  
(SHD) button  
PAGE button  
[Front]  
PB/B terminal  
PR/R terminal  
Y/G terminal  
KEY LOCK switch  
FORMAT switch  
1
2
4
3
DC IN 12V terminal  
DVI-D terminal  
1
9
2
3
4
5
6
7
8
8
5
7
4
6
3
10 11 12 13 14 15 16  
17 18 19 20 21 22 23 24  
2
1
SYNC OUT terminal  
EXT. SYNC terminal  
REMOTE terminal  
[Rear]  
Camera cable for  
“IK-HD1H” terminal  
Where the camera cable for “IK-HD1H” is connected.  
POWER LED  
POWER switch  
FILE button  
Illuminates to indicate the unit is powered on.  
Turns power on or off.  
To switch the scene files.  
GAIN button  
To change the gain mode.  
DISP button  
Changes the display mode.  
To switch and select menus.  
PAGE button  
MENU UPSHDbutton  
To select the function to be confirmed or changed on the menu.  
(Also used when performing auto shading correction.)  
MENU DOWN(SHD) button  
To select and confirm the function or to change the menu.  
DATA UPAWBbutton  
To change the value of the function selected by the MENU (UP/DOWN) button.  
(Also used when using AWB.)  
DATA DOWN  
ABBbutton  
To change the value of the function selected by the MENU (UP/DOWN) button.  
(Also used when using ABB.)  
8
 
DC IN 12V terminal  
Y/G terminal  
Accept a DC power input (12V).  
Outputs Y or G. (BNC connector)  
㽿PB/B terminal  
Outputs PB or B. (BNC connector)  
PR/R terminal  
Outputs PR or R. (BNC connector)  
REMOTE terminal  
EXT. SYNC terminal  
To connect to a RS-232C device for remote control function.  
Used when the camera output signal is synchronized to an external signal.  
(BNC connector)  
SYNC OUT terminal  
DVI-D terminal  
Output terminal for synchronization signal. (BNC connector)  
Outputs DVI-D to connect to a DVI monitor.  
Enables/disables buttons to .  
KEY LOCK switch  
FORMAT switch  
Switches between 59.94i and 50i.  
5
CONNECTION  
5
1
Standard Connection  
5. 1 -1 Analog Connection  
Lens  
Three Coaxial  
Cables 75㱅  
IK-HD1D  
(option)  
Y/PB/PR (not supplied)  
Camera Cable  
for IK-HD1D  
option  
Camera  
Control unit  
DC IN 12V  
3CCD HD Camera Head  
option  
IK-HD1H䋨  
DC power supply  
(option)  
HD monitor  
analog TV (not supplied)  
5. 1 -2 Digital Connection  
DVI-D Cable  
(not supplied)  
Lens  
IK-HD1D  
(option)  
DVI-D  
Camera Cable  
for IK-HD1D  
option  
Camera  
Control unit  
DC IN 12V  
3CCD HD Camera Head  
option  
IK-HD1H䋨  
DVI monitor  
DC power supply  
(option)  
(DVI-D) (not supplied)  
* Please use a DVI monitor applicable to 1080/59.94I or 1080/50I format signal.  
9
 
5
2
Caution on Connection  
Only use optional camera head model # IK-HD1H with this camera controller.  
The use of another head may cause damage to the control unit and camera head.  
When connecting the camera cables, be sure to turn off the camera control unit and  
any other equipment connected to it.  
For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA  
approved ungrounded type AC adaptor with the specifications described below.  
Power supply voltage  
Current rating  
Ripple voltage  
Connector  
12V DC 10%  
More than 1.5A  
(
)
Less than 50mV p-p  
HR10A-7P-4S by HIROSE electronics Co. Ltd  
Pins 1, 2 12V  
Pins 3, 4 GND  
If the securing screw on the connector of the camera cable loosens, noise may appear  
on the screen. Be sure to tighten the connector completely.  
5
3
Connection on Back Panel  
Back panel view  
1
2
4
3
1
9
2
3
4
5 6 7 8  
8
5
7
4
6
3
10 11 12 13 14 15 16  
17 18 19 20 21 22 23 24  
2
1
5
3A Connector Pin Assignments  
DC IN 12V  
REMOTE  
DVI-D  
1
2
3
4
5
6
7
8
NC  
1
2
3
4
5
6
7
8
Data2-  
Data2+  
9
Data1-  
17 Data0-  
18 Data0+  
1
2
3
4
+12V  
+12V  
GND  
GND  
NC  
10 Data1+  
RXD  
GND  
TXD  
NC  
NC  
NC  
Data2 Shield (GND) 11 Data1 Shield (GND) 19 Data0 Shield (GND)  
NC  
NC  
NC  
NC  
NC  
12 NC  
13 NC  
14 +5V  
15 GND  
16 NC  
20 NC  
21 NC  
22 Clock Shield (GND)  
23 Clock+  
24 Clock-  
Connector : TCS7926-18-301 (HOSIDEN)  
Mating Plug : TCP8580 (HOSIDEN)  
10  
 
6
OPERATION  
A camera head "IK-HD1H" needs to be connected to this camera control unit from this section on.  
Refer to the item “5. CONNECTION”, to connect the equipment correctly.  
Turn on the connected equipment and the camera.  
When using the camera for the first time and when replacing the camera cable and the camera head, be  
sure to perform the ABB adjustment, refer to the item “6.1 Automatic Black Balance”.  
Aim the lens at the object, adjust the lens iris adjustment, focus adjustment, etc.  
Refer to the item “6.2 White Balance”, and make the adjustment.  
Refer to the items “6.3 Scene File, 6.4 Gain, 7. MODE SETTING BY THE ON SCREEN DISPLAY”,  
and select the necessary items.  
When switching the FORMAT switch on the back panel of the unit, be sure to perform the ABB adjustment,  
refer to the item “6.1 Automatic Black Balance”.  
6
1
Automatic Black Balance  
Black balance adjustment is necessary to get the correct black picture level.  
Close the lens iris.  
If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the  
[DISP] button to disable the color bar pattern or the character display.  
Hold the [DATA DOWN] button for approx. 1 second.  
When the black balance adjustment operation starts, the character ABB blinks on the screen.  
When the black balance adjustment operation finishes, the character ABB stops blinking and the result  
appears for approx. 1 second.  
Display  
Meaning  
ABB OK  
ABB NG  
CLOSE LENS  
ABB NG  
Automatic black balance adjustment finished correctly.  
Automatic black balance adjustment cannot be performed because the lens iris  
is open. Close the lens iris.  
Automatic black balance adjustment cannot be performed.  
Operate the automatic black balance again.  
11  
 
6
2
White Balance  
For white balance adjustment of this unit, ATW (Automatic Tracking White balance), AWB (Automatic  
White Balance) and MANUAL (Manual white balance) adjustments are provided. Refer to the items “7.2  
(3) WHT BAL (White Balance), 7. MODE SETTING BY THE ON SCREEN DISPLAY”, select the desired  
mode.  
ATW  
AWB  
MANUAL  
Manual White Balance䋩  
Automatic Tracking  
Automatic White Balance䋩  
White Balance䋩  
The camera measures the  
Adjust white balance by  
Adjust the white balance  
manually using the WHT  
BAL menu while shooting  
the white object.  
Outline  
object color temperature and displaying the white object  
adjusts the white balance  
automatically.  
inside the area set by AWB  
menu and pressing the  
[DATA UP] button.  
Tracks variations of color  
Measurement accuracy is  
Artificial white balance setting.  
The manual adjustment is  
most effective under shooting  
conditions with no color  
Features temperature and adjusts white higher than ATW. This  
balance automatically.  
mode is effective when  
shooting under less varia-  
tions of color temperature.  
temperature variation.  
If illumination is low, white  
balance may not be corrected.  
Adjustment is performed by  
confirming with a vector  
scope.  
Notes  
AWB(Automatic White Balance)  
Set the MODE to AWB on the WHT BAL menu.  
Perform the C.TEMP (color temperature conversion) setting, if necessary.  
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)  
3200KAppropriate for indoor shooting.  
5600KAppropriate for outdoor shooting.  
If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the [DISP]  
button to disable the color bar pattern or the character display on the menu.  
Shoot a known white object entirely in the area set by the AWB menu (refer to the item “7.2 (3) (3.1) (d)  
Confirming the contents of the zone area selected by AWB” ) and push [DATA UP] button for approx. 1 second.  
The character AWB blinks on the screen when the AWB starts.  
The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.  
12  
 
Display  
AWB OK  
AWB NG  
Meaning  
Automatic white balance adjustment finished correctly.  
Automatic white balance adjustment cannot be performed because the video level is  
too low.  
LEVEL LOW  
Adjust the video level by increasing the illumination or opening the lens iris.  
Automatic white balance adjustment cannot be performed because the video level is  
too high.  
AWB NG  
LEVEL HIGH  
Adjust the video level by decreasing the illumination or closing the lens iris.  
Automatic white balance adjustment cannot be performed because the color  
temperature is too low.  
AWB NG  
C. TEMP LOW  
If the C.TEMP is set to 5600K, set to 3200K.  
If the message appears with the C.TEMP set to 3200K, change the illumination or  
use a color temperature conversion filter.  
AWB NG  
C. TEMP HIGH  
Automatic white balance adjustment cannot be performed because the color  
temperature is too high.  
If the C.TEMP is set to 3200K, set to 5600K.  
If the message appears with the C.TEMP set to 5600K, change the illumination or  
use the color temperature conversion filter.  
AWB NG  
Automatic white balance adjustment cannot be performed for other reasons. Such as  
no white area is included in an object, etc.  
MANUAL(Manual white balance)  
Set the MODE to MANUAL on the WHT BAL menu.  
(Refer to the item “7.2 (3) WHT BAL (White Balance)”.)  
Shoot a known white object, set the white balance by adjusting the levels of R GAIN and B GAIN on the  
menu, confirming with a monitor or a vector scope.  
(Refer to the item “7.2 (3) (3.3) Changing gain in MANUAL mode”.)  
13  
 
6
3
Scene File  
Five scene files (A, B, C, D, E) are available as user memories for this unit. These are chosen depending  
on shooting conditions. By using the [FILE] button, the camera operation is changed immediately from the  
currently selected Scene File to the next. (Refer to the item “7. MODE SETTING BY THE ON SCREEN  
DISPLAY”.)  
While any menu is displayed, pressing the [FILE] button will display the menu settings for the next Scene File:  
FILE A FILE B FILE C FILE D FILE E  
When the [FILE] button is pressed while the camera is in live image mode, the current scene file selection  
at that time is displayed for approx. 3 seconds in the upper right corner of the screen. If the [FILE] button is  
pressed again while the position is displayed, the scene file cycles as described above.  
6
4
Gain  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the desired video level.  
For gain adjustment of the unit, AUTO (Automatic gain control), MANUAL (Manual), OFF (0 dB) modes  
are provided. Select the mode on the GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.)  
AUTO(Automatic gain control)  
When the output is low, gain is automatically adjusted to a suitable video level.  
The maximum value of gain is 18dB, and can be set from 0 to 18dB in 1dB steps. (Refer to the item  
“7.2 (2) (2.1) Changing the maximum gain in AUTO (Automatic gain control) mode”.)  
Video level (LEVEL), peak average value ratio (PEAK/AVE), and measurement light area (AREA) is linked  
to the setting on the automatic shutter. (Refer to the item “7.2 (1) (1.1) Changing the setting in AUTO mode”.)  
MANUAL(Manual gain)  
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 18dB in 1dB steps.  
(Refer to the item “7.2 (2) (2.2) Changing gain in MANUAL mode”.)  
OFF  
Gain is fixed at 0 dB.  
Gain button  
ԘꢀIf the [GAIN] button is pressed, the current setting mode is on the GAIN menu for approx. 3 seconds.  
GAIN menu  
: OFF → GAIN OFF  
: AUTO → GAIN AUTO  
: MANUAL㧖㧖dB → GAIN dB  
㧖㧖” shows the setting gain in MANUAL mode.  
ԙꢀIf the [GAIN] button is pressed again while the current setting mode is displayed, the gain mode can be  
changed.  
GAIN of MAX GAIN in AUTO mode and MANUAL mode can not be changed.  
OFF  
AUTO  
MANUAL  
14  
 
Note:  
White, red, green, or blue dots may occur when the gain is increased. This is not a malfunction, just  
certain characteristics of the CCD becoming more visible.  
6
5
Shading Correction  
Due to the lens used or the environmental condition, color shading may occur at the upper and lower edge  
of the screen. If this happens, the shading correction function can be used to decrease the amount of color  
shading. For shading correction of the unit, SET (Automatic shading correction), MANUAL (Manual shading  
correction), and OFF (no shading correction) modes are provided. Select the mode on the OPTION menu.  
(Refer to the item “7.2 (7) (7.2) Changing shading correction mode”.)  
SET(Auto shading)  
If the color bar pattern is displayed on the screen or if the index menu/menu is displayed, press the  
[DISP] button to remove them from the screen.  
Push the [MENU UP] button for approx. 1 second.  
When the automatic shading correction operation starts, the character SHD blinks on the screen.  
When the automatic shading correction operation terminates, the character SHD ends blinking and the  
result is displayed for approx. 1 second.  
Display  
SHD OK  
Meaning  
Automatic shading correction operation finished correctly.  
SHD OK  
LIMIT  
SHD NG  
LEVEL LOW  
SHD NG  
Automatic shading correction operation finished, however, the correction  
necessary exceeds the camera’s range so the maximum possible value is applied.  
Automatic shading correction cannot be performed because the video level is too  
low. Adjust the video level by increasing the illumination or opening the lens iris.  
Automatic shading correction cannot be performed because the video level is too  
high. Adjust the video level by decreasing the illumination or closing the lens iris.  
LEVEL HIGH  
MANUAL(Manual Shading)  
Perform the correction amount setting on the OPTION menu, confirming with a monitor or a vector scope.  
(Refer to the “7.2 (7) (7.3) Changing manual shading correction mode”.)  
OFF  
The status is no shading correction.  
* Shading correction is only effective when the lens iris and zoom ratio is fixed. Use the unit with  
SHADING OFF for variable lens condition.s.  
Note:  
Before shading correction is performed, please shoot a known white object that fills the screen in  
the proper video level and set the automatic white balance (AWB) .  
15  
 
7
MODE SETTING BY THE ON SCREEN DISPLAY  
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The  
contents once set are memorized in the scene files (A, B, C, D, E) selected, so if the power turns off, it is  
unnecessary to set again when using the unit next time. When the setting is performed, select the menu of  
the item to be set.  
7
1
Using the Menus  
When the power turns on, the normal screen showing only the video signal appears. Change the output to  
each screen (video signal output, color bar screen, Index menu, menus, and area menu) by using the [DISP],  
[PAGE], [MENU UP], and [MENU DOWN] buttons.  
* A menu is selected when pushing the [PAGE] button after moving the “” on the screen by the [MENU  
UP], [MENU DOWN] button while the Index menu is displayed.  
POWER SW  
ON  
Video signal output  
Color bar screen  
PAGE  
Index menu  
PAGE  
DISP  
DISP  
DISP  
DISP  
PAGE  
Menus  
PAGE  
PAGE  
6.OPTION  
1.SHUTTER  
AUTO  
2.GAIN  
AUTO  
3.WHT BAL  
AWB  
4.PROCESS  
5.MATRIX  
6.SYNC  
INT  
PAGE  
PAGE  
PAGE  
PAGE  
PAGE  
GAMMA  
ON  
Y/Pb/Pr  
RGB  
ON  
GAMMA  
OFF  
MANU  
SS  
MANU  
OFF  
ATW  
OFF  
EXT.  
MANU  
16  
 
7
2
Menus  
Select the menu to change the setting by referring to the item “7.1 Using the Menus”.  
When the [MENU UP], [MENU DOWN] buttons are pushed, the “” on the screen moves up and down.  
Move the “” to the item whose setting you wish to change.  
1
SHUTTERElectronic shutter䋩  
The electronic shutter has four modes; AUTO, MANUAL, SS(Synchro. Scan).  
Press the “Page” button to enter the Shutter Page. Use the “Data Up/Down” buttons to select the Shutter  
Mode.  
AUTO  
MANUAL  
SS  
AUTO  
MANUAL  
The exposure time is controlled automatically to obtain the video level set.  
It is possible to select the exposure time from eleven speed settings; OFF (1/60s), 1/100s,  
1/125s, 1/250s, 1/500s, 1/1000s, 1/3000s, 1/5000s, 1/10000s, 1/30000s, 1/50000s.  
Note:  
When setting a rapid shutter speed, sensitivity degrades according to the speed.  
When a discharging light such as fluorescent lamp, etc. is used for the illumination,  
the flicker may be large.  
SS  
Shutter speed can be set by the horizontal scanning time (1H) unit.  
17  
 
11Changing the setting in AUTO mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
Shutter mode AUTO, MANUAL, SS  
Video level adjustment -100 to 100  
-- 1 SHUTTER -- <FILE A>  
Peak and average ratio adjustment 00 10 to 10 00  
Automatic shutter response speed adjustment 1 to 20  
MODE  
AUTO  
0
05 05  
10  
LEVEL  
PEAK AVE  
SPEED  
AREA  
Automatic shutter area selection  
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E  
PRESET A  
< MODE = AUTO>  
(a) Changing the video level in the automatic shutter mode  
Move the “” to LEVEL by pushing [MENU UP], [MENU DOWN] buttons.  
Select the video level by pushing [DATA UP], [DATA DOWN] buttons.  
The value increases by pushing [DATA UP]  
-100  
0
100  
The value decreases by pushing [DATA DOWN]  
(b) Changing the automatic shutter detection (ratio between peak and average value)  
Move the “” to PEAK/AVE by pushing [MENU UP], [MENU DOWN] buttons.  
Select the ratio between peak and average value by pushing [DATA UP], [DATA DOWN] buttons.  
(PeakAverage)  
The peak value increases by pushing [DATA UP]  
0010  
0505  
1000  
The peak value decreases by pushing [DATA DOWN]  
(c) Changing the automatic shutter response speed  
Move the “” to SPEED by pushing [MENU UP], [MENU DOWN] buttons.  
Select the response speed by pushing [DATA UP], [DATA DOWN] buttons.  
The response speed becomes faster by pushing [DATA UP]  
1
10  
20  
The response speed becomes slower by pushing [DATA DOWN]  
18  
 
(d) Changing the automatic shutter zone area  
Move the “” to AREA by pushing [MENU UP], [MENU DOWN] buttons.  
Select the measurement light area by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
PRESET A  
PRESET B PRESET C  
PRESET D  
PRESET E  
DATA DOWN䌝  
The available picture area is shown by the shading correction on the screen that is parted in 64.  
PRESET A  
PRESET B  
PRESET C  
PRESET D  
PRESET E  
Note:  
These available picture areas are not displayed on the screen.  
19  
 
12Changing the setting in MANUAL mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
Shutter mode AUTO, MANUAL, SS  
-- 1 SHUTTER -- <FILE A>  
Shutter speed setting  
OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s,  
1/3000s, 1/5000s, 1/10000s, 1/30000s, 1/50000s  
MODE  
MANUAL  
MANUAL  
1 10000s  
< MODE = MANUAL>  
(a) Changing the shutter speed  
Move the “” to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
OFF 1/100s 1/125s  
1/250s 1/500s 1/1000s 1/3000s 1/5000s 1/10000s 1/30000s 1/50000s  
DATA DOWN䌝  
13Changing the setting in SS (Synchro. Scan) mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
Shutter mode AUTO, MANUAL, SS  
Synchro. scan setting  
-- 1 SHUTTER -- <FILE A>  
MODE SS  
1
1125H  
560 1125H  
OFF  
SYNCHRO SCAN OFF  
< MODE = SS >  
(a) Changing the shutter speed setting  
Move the “” to SYNCHRO SCAN by pushing [MENU UP], [MENU DOWN] buttons.  
Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
1/1125H  
560/1125H  
OFF  
DATA DOWN䌝  
20  
 
2
GAIN (Video gain)  
GAIN has three modes; AUTO, MANUAL, OFF.  
Move the “” to MODE, push the [DATA UP], [DATA DOWN], and select one of the three modes :  
AUTO, MANUAL, OFF. In the OFF mode, gain is fixed to 0dB.  
21Changing maximum gain in AUTO (Automatic gain control) mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
-- 2 GAIN --  
<FILE A>  
Gain mode AUTO, MANUAL, OFF  
MODE  
MAX GAIN  
AUTO  
10dB  
Automatic maximum gain setting  
0dB to 18dB (1dB step)  
Move the “” to MAX GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of automatic maximum gain by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0dB  
18dB  
DATA DOWN䌝  
22Changing gain in MANUAL mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
-- 2 GAIN --  
<FILE A>  
Gain mode AUTO, MANUAL, OFF  
MODE  
MANUAL  
MANUAL  
0dB  
Manual gain setting  
0dB to 18dB (1dB step)  
Move the “” to MANUAL by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of manual gain by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0dB  
18dB  
DATA DOWN䌝  
21  
 
3WHT BAL(White Balance)  
The WHT BAL has three modes; AWB, ATW, MANUAL.  
Move the “” to MODE, push the [DATA UP], [DATA DOWN], and select one of the three modes :  
AWB, ATW, MANUAL.  
31Changing the setting in AWB(Automatic White Balance) mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
White balance mode setting AWB, ATW, MANUAL  
Color temperature setting 3200K, 5600K  
R PAINT adjustment -10 to 10  
-- 3 WHT BAL -- <FILE A>  
MODE  
AWB  
C TEMP  
3200K  
B PAINT adjustment -10 to 10  
R PAINT  
B PAINT  
0
0
AWB area  
AREA  
PRESET A  
PRESET A, PRESET B, PRESET C, PRESET D, PRESET E  
(a) Changing color temperature setting  
Move the “” to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.  
Select either 3200K or 5600K by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing R PAINT  
Move the “” to R PAINT by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of red paint by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
Red is increased.  
10  
10  
Red is decreased.  
(c) Changing B PAINT  
Move the “” to B PAINT by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of blue paint by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
Blue is increased.  
10  
10  
Blue is decreased.  
(d) Confirming the contents of the zone area selected by AWB  
Move the “” to AREA DISP by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired area by pushing [DATA UP], [DATA DOWN] buttons.  
22  
 
The available picture area is shown by the shading correction on the screen that is parted in 64.  
PRESET A  
PRESET B  
PRESET C  
PRESET D  
PRESET E  
Note:  
These available picture areas are not displayed on the screen.  
32Changing the setting in ATW(Automatic Tracking White balance) mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
White balance mode AWB, ATW, MANUAL  
-- 3 WHT BAL -- <FILE A>  
R PAINT adjustment -10 to 10  
B PAINT adjustment -10 to 10  
MODE  
R PAINT  
B PAINT  
ATW  
0
0
(a) Changing R PAINT  
Move the “” to R PAINT by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of red paint by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
Red is increased.  
10  
10  
Red is decreased.  
(b) Changing B PAINT  
Move the “” to B PAINT by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of blue paint by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
Blue is increased.  
10  
10  
Blue is decreased.  
23  
 
33Changing gain in MANUAL mode  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
White balance mode AWB, ATW, MANUAL  
Red gain adjustment -100 to 100  
-- 3 WHT BAL -- <FILE A>  
Blue gain adjustment -100 to 100  
MODE  
R GAIN  
MANUAL  
0
Color temperature setting 3200K, 5600K  
B GAIN  
0
C TEMP  
3200k  
(1) Changing the red gain  
Move the “” to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of red gain by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
Red is increased.  
10  
10  
Red is decreased.  
(2) Changing the blue gain  
Move the “” to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of blue gain by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
Blue is increased.  
10  
10  
Blue is decreased.  
24  
 
4PROCESS  
Move up and down  
Select the desired  
value by pushing  
DATA UP,DOWN  
by pushing  
MENU UP,DOWN  
Gamma correction ON, OFF  
-- 4 PROCESS --  
GAMMA ON/OFF ON  
<FILE A>  
Gamma correction level setting -10 to 10  
Detail gain setting -7 to 7  
GAMMA  
DTL GAIN  
M PED  
DNR  
0
0
0
Master pedestal setting -100 to 100  
Digital noise reduction ON,OFF  
OFF  
41Changing gamma correction ON/OFF  
Move the “” to GAMMA ON/OFF by pushing [MENU UP], [MENU DOWN] buttons.  
Select either ON or OFF by pushing [DATA UP], [DATA DOWN] buttons.  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
Gamma correction ON, OFF  
Detail gain setting -7 to 7  
-- 4 PROCESS --  
GAMMA ON/OFF OFF  
<FILE A>  
DTL GAIN  
M PED  
DNR  
0
0
Master pedestal setting -100 to 100  
Digital noise reduction ON,OFF  
OFF  
Menu when GAMMA OFF is selected.  
42Changing gamma correction level  
Move the “” to GAMMA by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of gamma correction level by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
Correction amount becomes larger.  
10  
DATA DOWN䌝  
10  
Correction amount becomes smaller.  
0
* When OFF is selected in GAMMA ON/OFF selection line, the gamma correction level change cannot  
be changed.  
25  
 
43Changing detail (outline) gain  
Move the “” to DTL GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of the detail gain by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
0
DATA DOWN䌝  
The detail increases.  
7
7  
The detail decreases.  
44Changing master pedestal  
Move the “” to M. PED by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
M PED rises  
100  
100  
M PED decreases  
0
DATA DOWN䌝  
45Changing DNR (Digital Noise Reduction)  
Move the “” to DNR by pushing [MENU UP], [MENU DOWN] buttons.  
Select either ON or OFF by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
When DNR is set to ON, noise is reduced, an accidental image might be outstanding while shooting  
moving objects.  
26  
 
5MATRIX(Matrix color correction)  
Move up and down  
Select the desired  
value by pushing  
DATA UP,DOWN  
by pushing  
MENU UP,DOWN  
Matrix color correction  
ON, OFF  
Yellow hue setting  
Red hue setting  
Red gain setting  
Green hue setting  
Green gain setting  
Blue hue setting  
Blue gain setting  
-- 5 MATRIX --  
<FILE A>  
Yellow gain setting  
Cyan hue setting  
MATRIX  
ON  
R HUE  
0
Ye HUE  
0
R GAIN  
G HUE  
G GAIN  
B HUE  
0
0
0
0
Ye GAIN  
Cy HUE  
Cy GAIN  
Mg HUE  
0
0
0
0
Cyan gain setting  
Magenta hue setting  
Magenta gain setting  
B GAIN  
0
Mg GAIN  
0
51Changing Matrix color correction ON/OFF  
Move the “” to MATRIX by pushing [MENU UP], [MENU DOWN] buttons.  
Select either ON or OFF by pushing [DATA UP], [DATA DOWN] buttons.  
52Changing MATRIX setting  
Move the “” to the desired item by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of color by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
15  
0
15  
DATA DOWN䌝  
* When matrix color correction is set to OFF, the color cannot be adjusted.  
27  
 
6SYNC  
When an external sync signal is input, the display changes from INT (internal sync) to EXT.(external sync)  
automatically.  
INT  
EXT  
61INT screen  
-- 6 SYNC --  
<FILE A>  
MODE  
INT  
62Changing EXT. setting  
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
Sync system display  
-- 6 SYNC --  
<FILE A>  
H PHASE -650 to 650  
MODE  
H PHASE  
EXT  
0
(a) Adjusting horizontal phase  
Move the “” to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
650  
0
650  
DATA DOWN䌝  
* If the phase difference is large, continuously pressing on the [DATA UP]/[DATA DOWN] button  
will make the setting shift by tens.  
28  
 
7OPTION  
Move up and down  
Select the desired  
value by pushing  
DATA UP,DOWN  
by pushing  
MENU UP,DOWN  
OUTPUT Y/Pb/Pr, RGB  
-- 7 OPTION  
--  
<FILE A>  
SHADING MODE SET, MANUAL, OFF  
RS232C baud rate 9600bps, 19200bps  
OUTPUT  
Y/Pb/Pr  
OFF  
SHADING  
BAUD RATE  
OSD OUTPUT  
9600bps  
ALL ON  
OSD OUTPUT ALL ON, Analog, Digital  
71Changing OUTPUT mode  
Move the “” to OUTPUT by pushing [MENU UP], [MENU DOWN] buttons.  
Select either Y/Pb/Pr or RGB by pushing [DATA UP], [DATA DOWN] buttons.  
72Changing shading correction mode  
Move the “” to SHADING by pushing [MENU UP], [MENU DOWN] buttons.  
Select SET, MANUAL or OFF by pushing [DATA UP], [DATA DOWN] buttons.  
73Changing manual shading correction mode  
Move the “” to MANUAL by pushing [MENU UP], [MENU DOWN] buttons.  
Select the desired value of manual shading correction by pushing [DATA UP], [DATA DOWN] buttons.  
DATA UP䌝  
128  
0
127  
DATA DOWN䌝  
* When the shading correction mode is set to anything other than MANUAL, the display turns off, so  
the setting cannot be made.  
29  
 
Move up and down  
by pushing  
MENU UP,DOWN  
Select the desired  
value by pushing  
DATA UP,DOWN  
OUTPUT Y/Pb/Pr, RGB  
-- 7 OPTION  
--  
<FILE A>  
RGB SYNC G, ALL ON, ALL OFF  
SHADING MANUAL Setting 128 to 127  
OUTPUT  
RGB  
G
RGB SYNC  
SHADING  
OFF  
BAUD RATE  
OSD OUTPUT  
9600bps  
ALL ON  
RS232C baud rate 9600bps, 19200bps  
OSD OUTPUT ALL ON, Analog, Digital  
74Changing RGB SYNC  
Move the “” to RGB SYNC by pushing [MENU UP], [MENU DOWN] buttons.  
Select G, ALL ON or ALL OFF by pushing [DATA UP], [DATA DOWN] buttons.  
* When Y/Pb/Pr is selected at OUTPUT, RGB SYNC change cannot be performed.  
75Changing RS232C baud rate  
Move the “” to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.  
Select either 9600bps or 19200bps by pushing [DATA UP], [DATA DOWN] buttons.  
76Changing OSD OUTPUT mode  
Ԙ Move the"→" to OSD OUTPUT by pushing [MENU UP], [MENU DOWN] buttons.  
ԙ Select either ALL ON, Analog, or Digital by pushing [DATA UP], [DATA DOWN] buttons.  
ꢀꢀ㧖ALL ON can be performed in both the analog and digital monitor.  
If Analog is selected, it outputs only for analog.  
If Digital is selected, it outputs only for digital.  
Please select a mode depending on the type of the monitor display that is connected.  
If incorrect mode is selected, the display might disappear.  
In that case, please cycle the power, and refer to section “7.2 (8) Returning to factory settings”.  
8Returning to factory settings  
The contents set of each scene file can be returned to the factory default status (preset status).  
(1) Select a scene file to set to the factory default status by [FILE] button.  
(2) If the color bar pattern or characters are displayed on the screen, press the [DISP] button to disable the  
color bar pattern and character display.  
(3) Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.  
(4) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed  
for approx. 1 second.  
30  
 
7
3
External Sync  
The unit can be used with an external sync signal connected to EXT. SYNC terminal on the rear panel.  
When the external sync signal is input, the camera automatically switches its sync from the internal sync to  
the external sync.  
EXT. SYNC input  
SYNC  
Operation  
External sync with SYNC  
1External sync signal input conditions  
SYNC75unbalanced䋩 䋺 0.6 V (p-p) standard  
2
3
External sync frequency range  
H : 33.716 Hz 35 ppm  
(59.94 Hz Setting)  
V : 59.94 Hz 35 ppm  
H : 28.125 Hz 35 ppm  
(50 Hz Setting)  
V : 50 Hz 35 ppm  
Using the unit with external sync signal  
Adjust H (Horizontal) phase if necessary to match the output of multiple cameras.  
When adjusting H (Horizontal) phase, refer to the item “7.2 (6) SYNC”.  
3. 1 H (Horizontal) phase adjustment  
External  
Observe the external sync signal and the video signal output  
waveform of the unit with a dual trace oscilloscope, and adjust  
H phase so that the H phases match.  
Sync. signal  
Match  
the phase.  
Camera  
Sync. output  
7
4
Synchro. Scan Operation  
The shutter speed can be set by the horizontal scanning period (1H).  
1
Setting by 1H  
1/1125H to 560/1125H stands for the setting by the 1H and the shutter speed can be set by the 1H.  
31  
 
8. BEFORE MAKING SERVICE CALL  
Symptom  
Items to be checked  
Is power supplied correctly?  
No picture  
Is the power switch on, and the power LED illuminated?  
Is the lens iris adjusted correctly?  
Are the camera and video cables connected correctly?  
Is the shutter mode set correctly?  
Is the monitor on, and in working condition?  
Is the monitor adjusted correctly?  
Poor color  
Is the white balance of the camera adjusted correctly?  
(in modes other than automatic tracking)  
Is the matrix color correction set correctly?  
Is the illumination sufficient?  
Is the camera cable connected securely?  
Noise appears  
32  
 
9. SPECIFICATIONS  
* These conditions are only satisfied when the camera control unit is connected to camera head model # IK-HD1H.  
Power supply  
12V DC10%  
Power consumption  
Pick-up system  
Image sensor  
Approx. 10.3 W (including a camera head)  
RGB, 3CCD, Micro prism system  
1/3 inch, ITCCD  
Output pixels  
Scanning system  
Scan frequency  
Horizontal : 1920, Vertical : 1080  
21 interlace  
[59.94 Hz setting] Horizontal : 33.716 kHz, Vertical : 59.94 Hz  
[50 Hz setting]  
Horizontal : 28.125 kHz, Vertical : 50 Hz  
Sync system  
Internal/External (Automatic switching)  
800TV lines standard  
800TV lines standard  
F6.859.94 Hz setting, 2000 lx, 3000 K, F7.450 Hz setting, 2000 lx, 3000 K䋩  
13 lx59.94 Hz setting, F2.2, sensitivity18 dB,  
11 lx50 Hz setting, F2.2, sensitivity18 dB䋩  
Horizontal resolution  
Vertical resolution  
Sensitivity  
Minimum illumination  
SN ratio  
56 dB standard (gain 0 dB, DNR OFF)  
0 to 40 (32F to 104F)  
Less than 90%  
Ambient temperature  
Ambient humidity  
Weight  
Approx. 725 g (1.60 lbs)  
External dimension  
110(W)40(H)186(D) mm  
(4.33”(W)1.57”(H)7.32”(D))  
(excluding protrusions)  
Scene file(user memories)  
White balance  
5 files (A, B, C, D, E)  
ATWAutomatic tracing balance, AWBAutomatic white balance  
Manual䋩  
MANUAL  
Gain  
AUTOAutomatic gain control, MANUALManual, OFF0 dB䋩  
Output signal  
Y/PB/PR or RGB : 0.7 V (p-p) standard 75 unbalanced, BNC connector  
DVI-D (digital RGB) : DVI-D terminal  
External sync input  
Sync signal output  
HD SYNC 0.6 V (p-p) 75  
[59.94 Hz setting] Horizontal : 33.716 kHz 35 ppm, Vertical : 59.94 Hz 35 ppm  
[50 Hz setting] Horizontal : 28.125 kHz 35 ppm, Vertical : 50 Hz 35 ppm  
unbalanced BNC connector  
SYNC : 0.6 V 0.1 V 75 unbalanced BNC connector  
[59.94 Hz setting] Horizontal : 33.716 kHz 35 ppm, Vertical : 59.94 Hz 35 ppm  
[50 Hz setting]  
Horizontal : 28.125 kHz 35 ppm, Vertical : 50 Hz 35 ppm  
RS-232C䋩  
Serial data interface  
Interface  
Optional parts  
IK-HD1H  
(3CCD HD Camera Head)  
EXCHD03 (Approx. 3 m (118”) Camera cable)  
EXCHD06 (Approx. 6 m (236”) Camera cable)  
EXCHD10 (Approx. 10 m (394”) Camera cable)  
EXCHD30 (Approx. 30 m (1181”) Camera cable)  
AC-Y415A (12V DC Power Supply)  
Design and specifications are subject to change without notice.  
33  
 
10. EXTERNAL APPEARANCE DIAGRAM  
Unit : mm [inch]  
㪈㪈㪅㪏  
㪲㪇㪅㪋㪍㪴  
㪈㪏㪍㩷㪲㪎㪅㪊㪉㪴  
[Front]  
㪋㪄㪤㪊㩷㪙㪛  
1
2
4
3
1
9
2
3
4
5
6
7
8
8
5
7
4
6
3
10 11 12 13 14 15 16  
17 18 19 20 21 22 23 24  
2
1
[Rear]  
㪉㪎㩷㪲㪈㪅㪇㪍㪴  
㪈㪊㪐㫧㪇㪅㪈㪌㩷㪲㪌㪅㪋㪎㪉㫧㪇㪅㪇㪇㪍㪴  
34  
 
Limited Warranty – TOSHIBA CCD Camera  
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranties  
with regard to this CCD Camera ("Product"). These limited warranties extend to the Original End-User ("You[r]").  
One (1)Year Limited Warranty of Labor and Parts  
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of  
purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does not  
perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an ISD  
Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the Product to the  
ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.  
Instruction Manual (Owner’s Manual):  
You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this Product. Before seeking warranty  
service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and follow the instructions to  
correct the problem.  
Your Responsibilities  
This Limited Warranty is subject to the following conditions:  
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.  
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with  
specifications during the Limited Warranty period.  
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.  
4. You must pack the Product in its original carton using the original packing material, then insert the original carton  
containing the Product into another carton with additional packing material before shipping the Product to an ASP.  
DISCLAIMERS:  
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO  
NOT ALLOWTHE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY  
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TOYOU.  
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE  
REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT  
COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE  
PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY  
DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY  
OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER  
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF TAIS, ITS PARENT COMPANY, OR  
AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.  
SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES  
FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TOYOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY  
VARY FROM STATE TO STATE.  
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE,  
ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S  
WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR  
AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR  
SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT  
COVERED BY THIS LIMITED WARRANTY.  
How to Obtain Warranty Service – Step-By-Step Procedures:  
To obtain warranty service, You should:  
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.  
2. Arrange for shipment of the Product to an ASP.  
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem and a copy  
of the bill of sale or proof of purchase.  
4. Prepay all transportation and insurance costs.  
Questions? If you have any questions, please check ISD’s Web Site or send an e-mail as follows:  
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the  
terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce  
any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof,  
is hereby limited to one (1) year from the date You discover or should have discovered the problem. This limitation does not  
apply to implied warranties arising under state law. Some states do not permit limitation of the time within whichYou may bring  
an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives  
You specific legal rights and You may also have other rights which vary from state to state.  
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.  
Imaging Systems Division  
9740 Irvine Boulevard, Irvine, CA 92618-1697  
Copyright © 2008 Toshiba America, Inc. All rights reserved.  
 

Telex Network Card XO 1 User Manual
Telex Video Gaming Accessories ps 4001 User Manual
Toastmaster Mixer TSM10 User Manual
Toshiba Recording Equipment ES8 User Manual
Transcend Information Network Card TS0MADP5 User Manual
True Fitness Exercise Bike LC900 User Manual
Velodyne Acoustics Home Theater System VMS 8 User Manual
Viking Range VGGT240SS User Manual
Viking Speaker System 25AE User Manual
Vivitar Digital Camera X327 User Manual