Taylor Scale TE10R User Manual

Caution: Changes or modifications not expressly approved by  
the party responsible for compliance could void the user's  
authority to operate the equipment.  
Auto Shut-Off Feature  
Precautions  
One Year Limited Warranty  
TE10R  
TThe scale will automatically shut off after 3 minutes of nonuse  
to conserve the battery. The auto-shut off feature can be  
disabled to allow the scale to operate continuously. To disable  
the auto-shut off feature:  
This scale is engineered to give you years of satisfactory  
service if you handle it carefully. Here are a few precautions:  
This product is warranted against defects in materials or  
workmanship for one (1) year from date of original purchase for the  
original purchaser. It does not cover damages or wear resulting  
from accident, misuse, abuse, or unauthorized adjustment and/or  
repair. Should this product require service (or replacement at our  
option) while under warranty, please pack the item carefully and  
return it prepaid, along with receipt showing date of purchase and  
a note explaining reason for return to:  
Note: This device complies with part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference  
that may cause undesired operation. This equipment has been  
tested and found to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC rules. These limits are  
designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if  
not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more  
of the following measures:  
1. Always read instructions thoroughly to ensure that you have  
the full benefit of all the unit's features.  
Digital Portion  
Control Scale  
Leading the Way in Accuracy  
1. While the scale is off, press and hold the “UNIT CONVERSION”  
button.  
2. While continuing to hold down the “UNIT CONVERSION”  
button, also press and hold down the “ON/OFF” button.  
3. The display will show “88888”, then “A-oF” The auto-off  
feature is now disabled. Release the buttons.  
4. To enable the auto-off feature again, repeat steps 1 and 2.  
A-on” will appear. The auto-off feature is now functional.  
2. DO NOT immerse unit in water, as doing so will cause  
damage to internal components and void the warranty. If  
you spill liquid on it, dry it immediately with a soft, lint-free  
cloth.  
3. DO NOT clean the unit with an abrasive or corrosive  
material. This may scratch the plastic parts and corrode the  
electronic circuits.  
4. DO NOT subject the units to excessive force, shock, dust,  
temperature or humidity. This may result in malfunction,  
shorter electronic life span, damaged battery and distorted  
parts.  
5. DO NOT tamper with the unit's internal components. Doing  
so will invalidate the warranty on the units and may cause  
damage. The unit contains no user-serviceable parts.  
6. This scale is an extremely sensitive weighing device. To avoid  
damage to the unit or the battery, do not store anything on  
the scale.  
7. Remove the battery if the scale will not be used for a long  
period of time.  
8. DO NOT dispose of batteries in fire. Disposing of this product  
in fire could cause batteries to explode or leak. Remove the  
battery if the unit will not be used for a long period of time.  
®
Taylor Precision Products, Inc.  
2220 Entrada Del Sol, Suite A  
Las Cruces, New Mexico 88001 USA  
Customer Service Phone: 1-800-225-4834  
Customer Service Fax: 1-575-526-4347  
Specifications  
Platform: 8-1/16” x 5”, Stainless steel (TE10ROS 10” x 6.75”)  
There are no expressed warranties except as listed above. This warranty  
gives you specific legal rights, and you may also have other rights which  
vary from state to state.  
For additional product information, or warranty information in Canada  
or elsewhere outside the USA, please contact us through  
Power: (1) 9 Volt battery (not included) or AC adaptor  
(included)  
Dimensions: 8-1/16” x 7-3/4” x 2-1/4”  
Weight: 2 lbs, 3 oz (TE10ROS 3lbs, 3oz)  
Capacity: 10 lb x 1/8 oz  
-Reorient or relocate the receiving antenna.  
-Increase the separation between the equipment and receiver.  
-Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected.  
10 lb x 0.05 oz  
©2013 Taylor Precision Products, Inc. and its affiliated companies, all  
rights reserved. Taylor® and Leading the Way in Accuracy® are  
registered trademarks of Taylor Precision Products, Inc. and its affiliated  
companies. All rights reserved.  
160 oz x 0.05 oz  
-Consult the dealer or an experienced radio/TV technician for  
help.  
5000 g x 1 g  
Resolution:0 to 10 lbs by 1/8 oz increments  
0 to 10 lbs by 0.05 oz increments  
0 to 5000 g by 1 g increments  
Accuracy: oz mode, +/-10 division  
g mode, +/-10 division  
Made to our exact specifications in China.  
NOT LEGAL FOR TRADE  
Instruction Manual  
TE10R - 11.13WC  
Thank you for purchasing a Taylor® Digital Portion Control Scale. Your  
scale is an example of superior design and craftsmanship. In order to  
optimize its function, be sure the read this instruction manual carefully  
before use. Keep instructions handy for future reference.  
General Operation (continued)  
Main Features (continued)  
• ON/OFF Button  
When pressed, turns the scale “ON” or “OFF”.  
• Backlit Display  
Will illuminate when weight is added or removed from  
platform. Press and Hold “ TARE ” to turn On/Off backlight  
function.  
• Moisture Resistant  
Components are sealed for resistance to moisture.  
• Auto Shut Off  
Scale powers off after 3 minutes of nonuse.  
• Low Battery Indicator  
Appears on LCD screen when battery is low.  
• Overload Signal  
Warning appears when weight is at 10% above the scale's  
rated capacity, even after tare up to 50% of capacity (in  
pound mode).  
Battery Installation  
General Operation  
The Digital Portion Control Scale operates with a rechargeable  
battery (included). To install and charge the battery:  
1. Remove the battery compartment door on the bottom of the  
scale.  
POWER  
Tare capability example: On a 10 pound scale (TE10), a load of 5 lbs  
(50%) can be tared out. Once tared out, an added weight of 11 lbs (full  
capacity plus 10%) can still be weighed without causing an overload  
condition.  
To turn the scale on, press the button marked “ON/OFF”. The display  
will first show “88888” followed by “  
”. To turn the scale off, push  
Description of Parts  
the “ON/OFF” button. The scale will remember the unit mode last  
If a load that exceeds 50% of the scale's capacity is tared out, the  
additional weight that can be measured will be reduced accordingly.  
shown, and this unit will display when the scale is turned on again.  
Ounces  
Display  
Hold  
Kilogram  
Display  
Pound  
Grams  
Display  
2. Plug the male connector of the rechargeable battery onto the  
female connector, which is located in the battery compartment.  
3. Place the rechargeable battery into the battery box.  
4. Replace the battery door.  
Hold  
Button  
On/Off  
Button  
Display  
Display  
UNIT CONVERSION  
HOLD OPERATION  
Press the Unit Conversion Button to switch from fractional ounces to  
decimal ounces to grams to ounces. When the scale is turned off, it  
will remember the unit mode last shown and will turn-on in that mode.  
HOLD  
NET  
The “HOLD” function may be used to lock the weight on the display for  
ten (10) seconds, even after the load is removed from the platform.  
g
o
z
k
g
lb  
5. To charge the battery, insert the connector plug of the adaptor  
into the jack at the back of the scale. Plug the other end of the  
adaptor into the proper electrical outlet. A red LED on the side of  
the scale will light up, indicating the battery is charging. When the  
LED light changes to green, the battery is completely charged.  
6. Allow at least 12 hours for the scale to charge completely. The  
scale will then operate continuously for approximately 14 hours.  
7. The battery life cycle is approximately 500 recharges. If the scale  
does not function properly after at least 12 hours of charging, the  
battery may need to be replaced. The scale will still operate on  
adaptor power if the battery is not charged.  
To use the hold function, press the “HOLD” button. A small triangle will  
appear in the upper left corner of the display next to the word “hold”,  
indicating the hold function is turned on. This triangle and the “hold”  
function will remain in place until the “HOLD” button is pressed again.  
This pressing of the “HOLD” button a second time will cancel the “hold”  
function, and the triangle will disappear from the display. While the  
scale is in “HOLD” mode:  
WEIGHING  
When the display shows “0”, the scale is ready to weigh an object. If  
the object exceeds the capacity of the scale by more than 10%, the  
display will show “Err” (for error). Until the overload condition is  
reached, additional objects may be placed on the platform. The  
display will show the sum of the weights of all the objects. When one  
of multiple objects is removed from the platform, the weight of the  
remaining objects will display.  
Scale Stable  
Display  
LCD  
Display  
LED  
Indicator  
Tare / Light  
Button  
Unit Conversion  
Button  
Place a load on the platform. When the weight is locked in, the triangle  
will begin to flash. When the load is removed from the platform, the  
display will continue to show the weight for ten seconds. After the ten  
second period is up, the triangle will stop flashing, and the display will  
show “0”. If the load is not removed from the platform, the triangle will  
continue to flash. The ten second “hold” period will begin once the  
load is finally removed from the platform.  
Main Features  
• LCD Screen  
1.0” digits display weight.  
• Hold Button  
8. To purchase a new rechargeable battery (model TERBAT), please  
contact customer service at 1-800-225-4834.  
9. There is also an AC adaptor included with this scale and can be  
used in place of the Rechargeable Battery.  
TARE OPERATION  
To tare (zero out) a load on the platform (example: the weight of a  
container), press the “TARE” button. The display will show the value  
0”.  
When pressed, the weight will display for ten seconds, even  
Before You Begin  
after the weight is removed.  
During the “TARE” mode, a new item can be added to the platform.  
The display will show the sum of the weights of the added items.  
Another item may be added, if desired. The display will show the sum  
of all additional item weights above and beyond the tared out load.  
During the ten (10) second period, the load can be tared out, causing  
the display to show “0”. And additional load will be displayed and held  
for another ten second period, etc.  
NOTE: please recycle or dispose of batteries per local regulations.  
1. Remove the scale from its box, along with its platform  
• Unit Conversion Button  
assembly and the adaptor.  
When pressed, converts the weight display from fractional oz  
WARNING: Batteries may pose a choking hazard. As with all small items,  
do not let children handle batteries. If swallowed, seek medical  
attention immediately.  
2. Install the platform assembly onto the scale by matching the  
plastic posts of the platform assembly with the mating holes  
on the top of the scale (no special orientation is required).  
to decimal oz to grams.  
If the “HOLD” button is pressed again, the scale will revert to its normal  
• Tare Button  
TARE CAPABILITY  
operating mode.  
When pressed, the scale reading returns to zero. Additionally,  
it can be used to offset the weight of a container or other  
object up to 50% of the scale's capacity.  
A load of up to 50% of the scale's capacity can be tared out, while still  
allowing the weighing of an additional object, up to the full capacity  
of the scale.  
PRECAUTION: Do not dispose of batteries in fire. Batteries may explode  
or leak. Remove the batteries if the scale will not be used for a long  
period of time.  
When the scale turns off, the hold function is cancelled. When the scale  
is turned on again, it will be in normal operating mode.  
 

Toastmaster Toaster TMT2 User Manual
Toshiba Projection Television TV GEN 03 User Manual
Tote Vision Flat Panel Television LCD 2300VT User Manual
Trane Thermostat RT SVX19A E4 User Manual
Trango Broadband Network Router Atlas5010 User Manual
Tripp Lite Network Card 2POSTRMKITWM User Manual
Tyan Computer Computer Hardware B5103G12S2 User Manual
Valcom Computer Hardware VIP 822 User Manual
Venturer Flat Panel Television PLV76176 User Manual
Vision Fitness Elliptical Trainer X6000DA User Manual