C8257-PD08423M
Size: A4
5.
Press “MODE” key to save and exit the setting
mode, or let it exit automatically 30 seconds
later without pressing any key.
TRANSMITTER:
6
6
NOTE:
WIRELESS THERMO CLOCK
MODEL IWA-80055
2
3
1
The alarm will be automatically turned on when you set
the alarm time.
USER’S INSTRUCTIONS
5
4
7
USING ALARM & TEMPERATURE ALARM
FUNCTIONS
1. LED indicator:
1.
2.
Set the alarm time as described in the previous
section.
Press “ALM ON/OFF” key once to turn on the
-
Flashes when the remote unit transmits a reading.
2. CHANNEL SLIDE SWITCH:
-
Assign the transmitter to Channel 1, 2 or 3.
(NOTE:The default and only effective channel
for receiver is Channel 1.)
alarm and snooze with the bell icon “
snooze icon “Zz” displayed on the LCD.
Press it twice to turn on the temperature alarm with
the icon “ ” displayed.
Press it again to turn off all of them until the
icons disappear.
” and
3.
4.
3. RESET:
-
Press it to restart the transmitter.
Thank you for your purchase of this wireless
thermo clock. The utmost care has gone into the design
and manufacture of your clock. Please read the
instructions carefully and keep the manual for future
reference.
The receiver unit has a clear, easy-to-read display that
shows the indoor/outdoor temperature, time, date, month
and day of the week . It is able to receive and display
readings from the remote sensor.
4. BATTERY COMPARTMENT:
NOTE:
-
Requires 2 AA size batteries (not included).
1.
2.
To activate the temperature alarm function,
ALARM must be on.
5. BATTERY DOOR:
The temperature alarm can be turned on 30
minutes earlier than the alarm only when the
transmitter’s temperature is below -3°C (26°F).
Once the snooze function is turned on, the 4-
step crescendo alarm will sound 7 times in 5-
minute interval. The alarm duration is 60 seconds.
Enter the snooze mode; press the “ALM ON/OFF”
key to stop the alarm completely and exit the snooze
mode.”
6. WALL-MOUNTING HOLDER:
-
Supports the transmitter in the wall mounting.
3.
4.
7. TABLE STAND:
The 433 MHz technology means no wire installation is
required and you can place the sensor anywhere you
like.
-
Use it to support the the sensor on a flat surface.
BEFORE USING THE TRANSMITTER
MAIN FEATURES:
1.
Remove the transmitter from the stand and
open the battery door.
S
N
O
O
Z
E
/
L
I
G
H
T
1
2.
Insert 2 AA size batteries into the battery
compartment. Make sure you insert them the
right way according to the polarity information
marked on the battery compartment.
Replace the battery door.
Alarm and Snooze ON Temperature Alarm ON Alarm/Temperature
Alarm/Snooze OFF
Remote Thermo Clock
IWA-80055
MODEL NO: IWA-80055
MADE IN CHINA
3.
4.
“Channel 1” must be selected for this model.
8
9
2
NOTE:
RESET
7
3
4
5
6
C/
F
Avoid placing the transmitter in direct sunlight, rain or
snow.
HOW TO READ INDOOR AND OUTDOOR
TEMPERATURE RECORDS
WEATHER STATION
1. SNOOZE / LIGHT:
-
-
Press it to turn on the backlight for 5 seconds.
Press it to stop the current alarm when it is
sounding.
Change the temperature unit to °C for Celsius or °F
for Fahrenheit by pressing the “ADJ · °C/°F” key.
1.
Remove the battery door and insert 3 AA size
batteries into the battery compartment. Make
sure you insert them the right way according to
the polarity information marked on the battery
compartment.
NOTE:
2. LCD display:
Displays the time, date, month, day of the week,
-
1.
2.
If no signals are received or the transmission is
interfered, “---” will appear on the LCD.
Relocate the clock or the transmitter in other
positions and make sure the transmission is within
the effective range of 100 feet approx.
2.
3.
Replace the battery door.
indoor/outdoor current temperature as well as the
maximum and minimum indoor/outdoor
temperature.
Press “RESET” key to restart the clock and it
will synchronize with the transmitter
automatically.
3. ALM ON/OFF:
-
3.
After several unsuccessful attempts to receive the
temperature signal, please remove the batteries
from the sensor and main display unit and start
the setup procedure again and decrease the
distance between the sensor and main display unit.”
NOTE:
Press it once to turn on the Alarm and Snooze;
press it twice to turn on the Temperature Alarm;
press it again to turn off all of them.
Press it to stop the current alarm when it is
sounding.
1.
2.
The building material and the position of receiver
and transmitter affect the effective range. So
try various locations to obtain the best result.
Place the unit away from metal objects and
electrical appliances to minimize the interference.
Position the receiver and transmitter within the
effective transmission range: 100 feet in usual
circumstances.
-
CHECKING AND DELETING MAX. /MIN.
TEMPERATURE RECORDS
4. MODE:
-
-
-
Press it to switch between normal time mode and
alarm time mode.
Press and hold it for 2 seconds to enter the time
setting mode.
In setting mode, press it to step the setting items.
1.
Press “MAX/MIN” key once to check the
maximum temperature records. Press it twice
to check the minimum records. Press it again to
exit.
TIME AND CALENDAR SETTING
2.
Press and hold “MAX/MIN” key for 3 seconds to
delete the maximum and minimum temperature
records.
5. ADJ · °C/°F:
-
-
1.
In normal time mode, press and hold “MODE”
key for 2 seconds until the HOUR digit flashes.
Press “ADJ · °C/°F” key to change its value.
Repeat the above operations to set time and
calendar in this order: Hour > Minute > Second >
12/24 Hr > Year > Month > Date.
Press “MODE” key to save and exit the setting
mode, or let it exit automatically 30 seconds
later without pressing any key.
Press it to switch between Celsius and Fahrenheit.
In setting mode, press it to change the setting
values.
2.
3.
MAX.temperature record MIN.temperature record
6. MAX / MIN:
-
Press it to check the minimum and maximum
temperature records.
Press and hold it for 3 seconds to delete the
maximum and minimum temperature records.
4.
-
ALARM TIME SETTING
7. RESET:
LOW BATTERY INDICATOR
-
-
Press it to reset all values to default values.
In case of malfunction, the unit may be required
to reset.
1.
In normal time mode, press “MODE” key to
enter the alarm time mode.
Press and hold “MODE” key for 2 seconds to
enter the alarm time setting mode until the
HOUR digit flashes.
Press “ADJ · °C/°F” key to change its value.
Repeat the above operations to set the alarm
Minute.
When the LCD becomes dim, replace with 3 AA size
batteries at once; while if the low battery indicator
” appears on the LCD, it indicates that the
battery power of the transmitter is not enough, and
you should replace the batteries at once.
2.
“
8. BATTERY COMPARTMENT:
Accommodates 3 AA size batteries.
-
3.
4.
9. FIXED TABLE STAND:
Use it to stand the clock on the desktop.
-
|