Power Adapter Notice:
Switch Settings:
1. When using in a stand-alone configuration, this product
is intended to be used and must be used only with a
Listed Direct Plug-In Power Unit marked “Class 2” and
rated at 9Vdc, 1 Amp.
“Termination” Switch: When attaching anywhere along
a coax cable except at the end, the Termination Switch
should be set to “Termination Out” (factory setting). When
attaching to the end of a cable, it can be set to
“Termination In.” Note that when the switch is set to
“Termination In,” an external termination element must
not be attached.
FlexPointTM 10FL/2 User Instructions
Description:
The FlexPointTM family of converters supports the
IEEE 802.3 and Ethernet Versions 1.0 / 2.0 standards.
They convert among 10BASE-FL fiber, 10BASE-2
thin coax and 10BASE-T twisted pair (UTP) media
types.
2. This product should always be used only with Omnitron
Supplied Power Unit model number 9113-PS.
LED Indicators:
WARNING!
Before installing and connecting the Power
Adapter verify that the power on the unit is
appropriate for your AC line voltage source.
LED
Color Description
The FlexPoint 10FL/2 converts from 10BASE-FL fiber
to 10BASE-2 coax. It uses ST fiber and BNC coax
connector. The following models are described here:
Power On
Jabber
Yellow Power applied
Red
Jabber condition
Fiber Link
Green Operational device detected at
the far end of fiber.
Mounting:
Model Fiber Type
Maximum Distance
The Omnitron FlexPoint 10FL/2 can be solo-mounted using
awall-mountingkit, orrack-mountedusinga5-positionspace-
saver shelf, FlexRack 5, or a 14-position high-density
FlexPoint Powered Chassis. When wall-mounting or shelf-
mounting, connect the power adapter unit.
Fiber Rx
Coax Rx
Collision
Green Received data on fiber line.
Green Received data on coax line.
Yellow Collision detected
4310 850 nm (multimode)
2 km
30 km
5 km
4311
1310 nm (single-mode)
4312 1310 nm (multimode)
For metal ST fiber connector, add M before the ‘dash’
in the Model Number. Example: 4310M-1, 4311M-0
Technical Support:
If you encounter problems in installing or maintaining
this product, contact Omnitron Technical Support:
Phone:
Fax:
Address: Omnitron Systems Technology, Inc.
140 Technology Drive, #500
When connecting the FlexPoint 10FL/2 at the end of a coax
segment, attach the coax cable directly into the FlexPoint’s
BNC coax connector. When connecting it along the coax
line (not at the end), use a “T” connector to tap into the cable.
The 10FL/2 provides a switch-selectable 50 ohm
termination that allows easy termination of the coax
cable. This function should be used only when the
FlexPoint is connected at the end of a segment.
(949) 250-6510
(949) 250-6514
Attach the fiber cables to the FlexPoint’s connectors. The
FlexPoint’s transmit (Tx) must attach to the receive side on
the device at the far end of the fiber and the receive (Rx)
must attach to the transmit side.
Note that the total length of the coax cable must not
exceed 185 meters and the number of stations on the
coax segment must not exceed 30 stations (per IEEE
802.3 specification).
Irvine, CA 92618 USA
E-mail:
URL:
product to Buyer’s designated US address using
Omnitron’s standard shipping method.
Warning
Notes:
The operating description in this Instruction Manual is
for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualified and certified to do so by Omnitron
Systems Technology, Inc.
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
_____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
Limitation of Warranty
The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or
maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized
modifications or tampering with equipment (including
removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or
misuse, or operating outside the environmental
specification of the product (including but not limited to
voltage, ambient temperature, radiation, unusual dust,
etc.), or improper site preparation or maintenance.
Caution
All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.
Warranty
This product is warranted to the original purchaser
against defects in material and workmanship for a period
of TWO YEARS from the date of shipment. A LIFETIME
warranty may be obtained by the original purchaser by
REGISTERING this product with Omnitron within 90 days
from the date of shipment. TO REGISTER, COMPLETE
AND MAIL OR FAXTHE REGISTRATION PORTION OF
THIS INSTRUCTION MANUAL TO THE INDICATED
ADDRESS. During the warranty period, Omnitron will,
at its option, repair or replace a product which is proven
to be defective.
No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for any
direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal
theory.
For warranty service, the product must be sent to an
Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the
Form:040-04310-001C 11/07
|