M O
D
E L
SVL-2
SVL-2
SPEAKER SELECTION/VOLUME CONTROL SYSTEM
NILES
®
I N S T A L L A T I O N & O P E R A T I O N G U I D E
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Feat ures and Benefit s
The SVL-2 offers a number of improvements over other
speaker selector/volume controllers:
● The SVL-2 uses 12 position volume controls which are
superior to 10 position designs. You get a broader range of
adjustment —there are 10 steps of attenuation instead of 8.
Steps 11-6 attenuate -3 dB per step; steps 5-2 are 6 dB per
step. Step 12 is "full-on" and step 1 is "full-off".
TECH
SUPPORT
HOTLINE
If you have
questions regarding
the operation of the
Niles SVL-2, contact
your local Niles
● Greater dynamic range —you get 42 dB of total attenua-
tion instead of the usual 20 or 30 dB.
● POP-FREE switching between all steps.
dealer or Niles
Customer Service at
1-800-289-4434.
● Pre-printed Room Labels are included for easy identification
of speaker ON/OFF buttons.
● Isolated right and left channel ground returns make the
SVL-2 compatible with all types of amplifiers.
● Self-cleaning, silver-plated switch contacts assure many
years of trouble free use.
● Printed circuit board design assures high reliability.
2
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
● Spring-loaded push terminal connectors accommodate up
to 14 gauge wire or "pins", making the SVL-2 compatible
with most "high-definition" speaker cables.
● 100% tested, electronically and acoustically, for frequency
response, distortion and power handling.
● Only 8 1/2" wide. Match the width of 17" components by
combining with another Niles 1/2 width product.
● May be used with 4, 6 or 8-ohm speaker systems.
● Ideal for both home and commercial sound installations.
● Only a wire stripper is required for installation.
● Power handling: 100 watts/channel continuous music
power.
● Frequency response: 20 Hz to 20 kHz +/-1.2 dB.
● Ten year parts and labor warranty.
● Proudly made in the USA.
3
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Inst allat ion Considerat ions
SVL-2 Power Handling
TOOLS
REQUIRED
The SVL-2 is designed for use with a receiver or amplifier hav-
ing a maximum power output of 100 watts per channel at 8
ohms. Damage caused by the use of a higher-power receiver
or amplifier will void the warranty. Consult your Niles dealer,
or receiver/amplifier manufacturer, if you are uncertain about
the power rating of your receiver or amplifier.
• Wire Stripper
IMPORTANT: DO NOT USE THE SVL-2 WITH AMPS OR
RECEIVERS RATED AT MORE THAN 100 WATTS PER
CHANNEL RMS AT 8 OHMS.
IMPORTANT
DO NOT use the
SVL-2 with amps
or receivers rated
at more than 100
watts per channel
RMS at 8 ohms.
Amplifier Impedance Load
As more pairs of speakers are parallel connected to a receiver
or amplifier, the overall system impedance becomes lower.
For example, if two pairs of 8-ohm speakers are connected in
parallel, the impedance will be 4 ohms, two pairs of 4-ohm
speakers in parallel become 2 ohms, and so on.
Most receivers or amplifiers are not rated for use below a 4
ohm load. Most manufacturers do not recommend connect-
ing two pairs of 4-ohm speakers without using some form of
impedance correction.
4
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
The SVL-2 includes impedance correction circuitry which
protects your receiver or amplifier from low impedance
loads. The circuitry assures that your receiver or amplifier will
see a safe operating load, even when two pairs of 4-ohm
speakers are playing at the same time.
Type of Speaker Wire
"TECH TIP"
For most applications, we recommend you use 16 or 18
gauge stranded copper speaker wire for the SVL-2 connec-
tions. For wiring runs longer than 80 feet, 14 gauge wire is
recommended. Using speaker wire larger than 14 gauge for
the SVL-2 connections is not recommended —the wire may
not fit into the connectors. Never use solid-core, aluminum,
or "Romex" type wire with the SVL-2. When running speaker
wires inside walls, most states and municipalities in the U.S.
specify that you must use a special type of speaker wire.
Usually, the requirement is that the wire has a specific "CL"
fire rating, such as "CL-2" or "CL-3". Consult your Niles deal-
er, building contractor, or local building and inspection
department if unsure about which type of wire is best for
your application.
Wire size is
expressed by it's
AWG (American
Wire Gauge)
number. The lower
the AWG number,
the larger the wire,
i.e., 12 AWG wire is
physically larger
than 14 AWG.
Avoiding Interference
Speaker wires can act as an antenna for electrical noise.
Locating speaker wires too close to a light dimmer or switch
may cause a "buzzing" or "popping" sound to be heard
thought the speakers. If you must locate the SVL-2 wiring
5
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
near electrical devices, route the speaker wires several feet
away from the electrical wiring.
Using the SVL-2 with Tube-Type Amplifiers
Virtually all tube amplifiers must have a load connected at all
times. If the amplifier to be connected to the SVL-2 is a tube
amplifier, be sure to always have at least one pair of speakers
switched on at all times. An alternative is to permanently
connect a 150 ohm, 5 watt resistor across the tube amplifier's
output in parallel with the SVL-2. See (Figure 1) for hookup
diagram.
Tube Amplifier
Figure 1
Using a
Tube Amplifier
150
150
Niles SVL-2
AMPLIFIER
SPEAKER 2
SPEAKER 1
+
-
+
-
+
-
+
-
N
I
L
E
S
Niles Audio
Corporation, Inc.
Miami, Florida USA
L
R
L
R
L
R
6
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
12 position volume control
provides greater attenuation
than conventional 10 position
designs.
Recessed
areas for
custom room
labels.
SVL-2 SPEAKER SELECTION/ VOLUME CONTROL SYSTEM
PROTECTION
Attractive
low-profile
design.
N
I
L
E
S
1
2
Simple
push-button
operation.
Connect up to two pairs
of speakers.
Protection switch safeguards your
receiver or amplifier even with
both pairs of speakers playing.
AMPLIFIER
+
SPEAKER 2
SPEAKER 1
+
-
+
-
+
N
I
L
E
S
-
-
Niles Audio
Corporation, Inc.
Miami, Florida USA
L
R
L
R
L
R
Spring
loaded push
connectors.
7
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Inst allat ion
1. Select a convenient location for the SVL-2.
2. Run all the necessary wiring to the SVL-2. Label the wires for
future reference. See (Figure 2).
Receiver
TUNER 94.9
Figure 2
Wiring Diagram
15
Niles SVL-2
AMPLIFIER
SPEAKER 2
SPEAKER 1
+
-
+
-
+
-
+
-
N
I
L
E
S
Niles Audio
Corporation, Inc.
Miami, Florida USA
L
R
L
R
L
R
Speaker
Pair 2
Speaker
Pair 1
8
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
3. Make the connections to the SVL-2. Strip 3/ 8" of
insulation from the end of each wire. Tightly twist the
end of each wire until there are no frayed ends. Insert
each wire in to th e ap p rop riate h ole on th e sp rin g -
load ed con n ector term in als. Be certain th at p rop er
phasing is observed —connect the positive terminals on
the SVL-2 to the positive terminals on the amplifier and
speakers and the negative terminals on the SVL-2 to the
negative term inals on the am plifier and speakers. See
(Figure 3).
4. Locate the pre-printed Room Labels. Affix the appropriate
label to the recessed area over each ON/OFF selector button.
Figure 3
Removing the
Connectors
9
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Operat ion
The are two ways to use the SVL-2. You may play and adjust
the volume of either pair of speakers independently, or both
pairs simultaneously.
If you intend to play both pairs simultaneously, and either
pair is less than 8 ohms, you will need to become familiar
with the operation of the SVL-2's PROTECTION button.
"TECH TIP"
If your amplifier or
receiver has "A"
and "B" speaker-
pair outputs,
connect the SVL-2
to the "A" outputs.
Do not connect
anything to "B".
This will prevent
the amplifier or
Playing One Pair of Speakers At a Time
1. Make sure the amplifier or receiver power is OFF and set
the volume to minimum.
2. Set the SVL-2 volume control for the speaker pair you wish
to play to maximum (fully clockwise).
3. Locate the ON/OFF button on the SVL-2 which corre-
sponds to the speaker pair you wish to play. Set it to the ON
position.
receiver from driving
an unusually low
impedance load.
4. Turn on the amplifier or receiver and select as source, such
as the tuner or CD player.
5. Slowly turn up the amplifier or receiver volume and set it
to a comfortable (not maximum) listening level. Be careful
not to overdrive or "clip" your am plifier. If the sound
becomes muddy or distorted, you have reached the limit of
your amplifier's volume capability and should quickly reduce
the volume to avoid damaging your speakers.
10
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
6. Using the appropriate volume control on the front of the
SVL-2, adjust the volume of the speakers to the desired listen-
ing level.
7. You can turn off the speakers by turning the appropriate
volume control on the SVL-2 fully counter-clockwise, or by
pressing the ON/OFF button.
Playing Two Pairs of Speakers Simultaneously
1. Make sure the amplifier or receiver power is OFF and set
the volume to minimum.
2. On the right side of the SVL-2's front panel is a button
labeled PROTECTION. This button activates the SVL-2's imped-
ance correction circuitry. The circuitry assures that your receiv-
er or amplifier will see a safe operating load when playing two
pairs of speaker simultaneously. Since most receivers and
amplifiers are not rated for use below a 4 ohm load, you will
need to activate the PROTECTION button whenever the over-
all system impedance might fall below 4 ohms. Use the follow-
ing chart as a guide for setting the PROTECTION button.
When playing the following speakers:
1 or 2 pair of 8-ohm speakers
1 pair of 4-ohm speakers
The Protection button should be:
OFF
OFF
ON
2 or more pairs of 4-ohm speakers
Any combination of 4 and 8 ohm speakers
ON
Set the PROTECTION button to the correct position using the chart shown above.
11
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
3. Set both SVL-2 volume controls to maximum.
4. Locate the ON/OFF buttons on the SVL-2. Set both to the
ON position.
"TECH TIP"
You will need to
5. Turn on the amplifier or receiver and select as source, such
as the tuner or CD player.
activate the SVL-2's
PROTECTION button
whenever the overall
system impedance
might fall below
6. Slowly turn up the amplifier or receiver volume and set it
to a comfortable (not maximum) listening level. Be careful
not to overdrive or "clip" your am plifier. If the sound
becomes muddy or distorted, you have reached the limit of
your amplifier's volume capability and should quickly reduce
the volume to avoid damaging your speakers.
4 ohms.
7. Using the appropriate volume controls on the front of the
SVL-2, adjust the volume of the speakers to the desired listen-
ing level.
8. You can turn off the speakers by turning the appropriate
volume controls on the SVL-2 fully counter-clockwise, or by
pressing the appropriate ON/OFF buttons.
12
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
Balancing Speaker Volume
The volume control on your receiver or amplifier serves as
the "master" volume for all speaker pairs connected.
The volume level of the speakers may vary from room to
room. This is caused by several factors. Two lesser factors are
the size of the speaker and its efficiency. The largest factor is
the physical size of the room.
The SVL-2's volume controls allow you to adjust the volume
of each speaker pair individually. You can leave the amplifier
or receiver volume set at one position and use the SVL-2 vol-
ume controls exclusively.
13
S
P
E
A
K
E
R
S
E
L
E
C
T
I
O
N
/ V
O
L
U
M
E
C
O
N
T
R
O
L
S
Y
S
T
E
M
SPECIFICATIONS
Audio Power Handling
100 watts/channel continuous music power
Frequency Response
+/- 1.2 dB from 20 Hz to 20 kHz
Mounting
Table-top component
Wiring Requirements
Individual runs of 2-conductor speaker wire. Connectors
accommodate wire sizes 14-22 gauge (16 gauge recommended)
Overall Dimensions
8-1/2" wide x 2" high x 7-1/4" deep
Weight
3 lb.
14
NILES ®
®
Niles Audio
Corporation
www.nilesaudio.com
© 1999 Niles Audio Corporation. All rights reserved. Because Niles constantly strives to improve the
quality of its products, Niles reserves the right to change product specifications without notice. Niles
and the Niles logo are registered trademarks of Niles Audio Corporation. Printed in USA 4/96
DS00094A
12331 S.W. 130 Street
Miami, Florida 33186
Tel: (305) 238-4373
Fax: (305) 238-0185
|