MIL-C1111
Re g u la t o r y A p p r o v a ls
•FCC Class A
•UL 1950
•CSA C22.2 No. 950
•EN60950
MIL-C1 1 1 1
Co a x to Ba se -T (UTP)
Me d ia Co n ve rte r
In sta lla tio n Gu id e
•CE
•– EN55022 Class B
•– EN50082-1
Ca n a d ia n EM I N o t ice
This Class A digital apparatus meets all the requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.
Eu r o p e a n N o t ice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC)
•
and the Low Voltage Directive (73/23/EEC) issued by the commission of the European
Community. Compliance with these directives implies conformity to the following
European Norms:
500 mA
•EN55022 (CISPR 22) - Radio Frequency Interference
•EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity
•EN60950 (IEC950) - Product Safety
MIL-C1111
Fiv e Ye a r W a r r a n t y
Ethernet
MiLAN Technology warrants to the original consumer or purchaser that each of its
products, and all components thereof, will be free from defects in material and/or
workmanship for a period of five years from the original factory date. Any warranty
hereunder is extended to the original consumer or purchaser and is not assignable.
MiLAN Technology makes no express or implied warranties including, but not limited to,
any implied warranty of merchantability or fitness for a particular purpose, except as
expressly set forth in this warranty. In no event shall MiLAN Technology be liable for
incidental or consequential damages, costs, or expenses arising out of or in connection
with the performance of the product delivered hereunder. MiLAN Technology will in
no case cover damages arising out of the product being used in a negligent fashion or
manner.
COAX to 10BASE-T
IEEE 802.3 Compliant
Tr a d e m a r k s
© 2000 MiLAN, the MiLAN logo, and MiLAN Technology are either trademarks or registered trademarks of
Digi International, Inc. in the United States and/or other countries. All other trademarks are the property of
their respective holders.
To Co n t a ct M iLA N Te ch n o lo g y
For prompt response when calling for service information, have the following information ready:
Product serial number and rev; date of purchase; vendor or place of purchase.
You can reach MiLAN Technology technical support at: support@milan.com
Telephone: +1.408.744.2751 Fax: +1.408.744.2771
POWER
TX ACTIVE
TX LINK
COAX ACTIVE
COAX ENABLE
MiLAN Technology 1299 Orleans Drive, Sunnyvale, CA 94089-1138 United States of America
Telephone: +1.408.744.2775 Fax: +1.408.744.2793
Coax
UTP
info@milan.com
© Copyright 2000 MiLAN Technology
Printed in the U.S.A.
In sta lla tio n
LEDs
Follow the steps given below to install the MIL-C1111:
1. Attach a UTP cable from network to MIL-C1111’s RJ-45 port.
2. Attach a T-type BNC connector from network cabling to the BNC
connector.
3. Plug the power adapter into an AC outlet and connect the power
adapter cord to the unit.
EMI Note: Use shielded UTP (CAT 5) cabling for CISPR 22 classB.
Co n fig u ra tio n -Te rm in a tio n Sw itch
Next to the coax cable connector, there are DIP switches that
control the 50 Ohm internal resistor. Both switches are shipped in
the “up” position (default, no termination).
•
TP ACT: Amber, indicates a packet activity on the 10BASE-T net-
work.
•
COAX ACT: Amber, indicates a packet activity on the 10BASE2
network.
•
•
TP LINK: Green, there is a good link on the 10BASE-T network.
COAX ENAB: Green, coax connection is established.
Ca b lin g O p tio n s: MDI-X/ MDI Sw itch
The MDI-X/MDI switch is located on the side of the unit. This
switch enables a quick configuration of the 10BASE-T port.
Cables used when the switch is in the MDI-X position:
•
For a hub or repeater, use a swap cable (pins are connected 1 to 3,
2 to 6, 3 to 1, 6 to 2).
Co n fig u ra tio n O p tio n s
1. If the MIL-C1111 is connected to the end of a multinode segment
•
For a workstation or PC, use a straight-through cable (pins are
connected 1 to 1, 2 to 2, 3 to 3, 6 to 6).
without a T-connector and terminator, enable 50 Ohm resistor by
•
•
Setting switch 1 “up”
Setting switch 2 “down”.
Cables used when the switch is in the MDI position:
•
For a hub or repeater, use a straight-through cable (pins are con-
nected 1 to 1, 2 to 2, 3 to 3, 6 to 6.
2. If the MIL-C1111 is connected to a single-nod without a T-type
connector and terminator on a coax cable of less than one meter’s
length:
•
For a workstation or PC, use a swap cable (pins are connected 1 to
3, 2 to 6, 3 to 1, 6 to 2.
•
Set both switches in the “down” position.
RJ-4 5 Sp e cifica tio n s
Note: For this configuration, you do not need a 50 Ohm
terminator on the coax segment of the MIL-C1111’s BNC
connector.
4
5
3
6
MDI
Pin 1=TX+
Pin 2=TX-
Pin 3=RX+
Pin 6=RX-
7
2
8
MDI-X
1
Pin 1=RX+
Pin 2=RX-
Pin 3=TX+
Pin 6=TX-
©Copyright 2000 MiLAN Technology PN 90000213 Printed in the USA
|