JVC VCR HR FS1U User Manual

VIDEO CASSETTE RECORDER  
HR-FS1U  
INSTRUCTIONS  
LPT0510-001B  
COPYRIGHT © 2000 VICTOR COMPANY OF JAPAN, LTD.  
Printed in China  
1100 IYVfIDfBJ  
Dear Customer,  
Declaration of Conformity  
Thank you for purchasing the JVC VHS video cassette recorder.  
Before use, please read the safety information and precautions to  
ensure safe use of your new VCR.  
Model Number:  
Trade Name:  
HR-FS1U  
JVC  
Responsible Party: JVC Americas Corp.  
Address:  
1700 Valley Road Wayne, N.J. 07470  
CAUTIONS  
Telephone Number: 973-315-5000  
This device complies with Part 15 of FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this  
device must accept any interference received, including  
interference that may cause undesired operation.  
Failure to heed the following precautions may result in damage  
to the VCR, Remote or video cassette.  
1. DO NOT place the VCR …  
… in an environment prone to extreme temperatures or  
humidity.  
The lightning flash with arrowhead symbol, within  
an equilateral triangle, is intended to alert the user  
to the presence of uninsulated “dangerous voltage”  
within the products enclosure that may be of  
sufficient magnitude to constitute a risk of electric  
shock to persons.  
… in direct sunlight.  
… in a dusty environment.  
… in an environment where strong magnetic fields are  
generated.  
… on a surface that is unstable or subject to vibration.  
2. DO NOT block the VCRs ventilation openings.  
3. DO NOT place heavy objects on the VCR or on the Remote.  
4. DO NOT place anything which might spill on the top of the  
VCR or on the Remote.  
The exclamation point within an equilateral triangle  
is intended to alert the user to the presence of  
important operating and maintenance (servicing)  
instructions in the literature accompanying the  
appliance.  
5. AVOID violent shocks to the VCR during transport.  
VCR Plus+ and PlusCode are registered trademarks of Gemstar  
Development Corporation.  
WARNING:  
The VCR Plus+ system is manufactured under license from  
Gemstar Development Corporation.  
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE  
THIS UNIT TO RAIN OR MOISTURE.  
For Customer Use:  
CAUTION:  
Enter below the Model No. and Serial No. which are located  
on the rear of cabinet. Retain this information for future  
reference.  
This video cassette recorder should be used with AC 120Vd,  
60Hz only.  
To prevent electric shocks and fire hazards, DO NOT use any  
other power source.  
Model No.  
Serial No.  
CAUTION:  
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF  
PLUG TO WIDE SLOT, FULLY INSERT.  
ATTENTION:  
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA  
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE  
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU  
FOND.  
Note to CATV system installer:  
Cassettes marked “VHS” (or “S-VHS”) can be used with this  
video cassette recorder. However, S-VHS recording is not  
possible with this model.  
This model is equipped with SQPB (S-VHS QUASI PLAYBACK)  
that makes it possible to play back S-VHS recordings with  
regular VHS resolution.  
This reminder is provided to call the CATV system installers  
attention to Article 820-40 of the NEC that provides guidelines  
for proper grounding and, in particular, specifies that the cable  
ground shall be connected to the grounding system of the  
building, as close to the point of cable entry as practical.  
HQ VHS is compatible with existing VHS equipment.  
As an ENERGY STAR® Partner, JVC has determined that this  
product or product model meets the ENERGY STAR® guidelines  
for energy efficiency.  
CAUTION:  
Changes or modifications not approved by JVC could void  
users authority to operate the equipment.  
 
SERVICING  
1. Servicing  
Buttons, Connectors  
and Indicators  
Front Panel  
If your product is not operating correctly or exhibits a marked  
change in performance and you are unable to restore normal  
operation by following the detailed procedure in its operating  
instructions, do not attempt to service it yourself as opening or  
removing covers may expose you to dangerous voltage or other  
hazards. Refer all servicing to qualified service personnel.  
2. Damage Requiring Service  
Unplug this product from the wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power supply cord or plug is damaged.  
b. If liquid has been spilled, or objects have fallen into the  
product.  
c. If the product has been exposed to rain or water.  
d. If the product does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as an improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the product to its normal operation.  
Cassette  
loading slot  
Display  
panel  
e. If the product has been dropped or damaged in any way.  
f. When the product exhibits a distinct change in performance—  
this indicates a need for service.  
3. Replacement Parts  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer or which have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock or other hazards.  
Remote  
sensor  
4. Safety Check  
Upon completion of any service or repairs to this product, ask the  
service technician to perform safety checks to determine that the  
product is in safe operating condition.  
Rear Panel  
How to use the Remote  
Before use, insert two AA size batteries into the Remote with the  
polarity ( and ) matched correctly as indicated on the battery  
compartment or on the lid.  
AC power  
cord  
The Remote can operate most of your VCRs functions, as well as  
basic functions of TV sets, cable boxes and DBS receivers.  
Point the Remote toward the remote sensor on the target  
component.  
The maximum operating distance of the remote control is about  
8 m.  
NOTE:  
If the Remote does not work properly, remove its batteries, wait  
for a few seconds, replace the batteries and then try again.  
Video heads cleaning  
Use a dry cleaning cassette TCL-2UX when:  
Rough, poor picture appears while a tape is played back.  
The picture is unclear or no picture appears.  
USE CLEANING CASSETTEappears on the screen (only with  
SUPERIMPOSEset to ON).  
Display panel  
When a tape is paused, the indicators blink.  
When a tape is being fast forwarded or rewound, the  
indicators light in sequence quickly in the clockwise or  
counterclockwise direction; this represents the rapidly  
rotating tape hubs.  
When there is no tape in the VCR, the indicators are all off.  
D Back light  
Playback : green  
Recording : red  
Error : red (blinking)  
Stop : orange  
A Timer mode indicator  
Power off : green (dark)  
E Tape speed indicator  
F Channel and auxiliary input/Clock time  
G REC indicator  
B VCR mode indicator  
C Tape movement indicator  
When a tape is being played or recorded, the indicators light  
in sequence slowly in a clockwise direction; this represents  
the rotating tape hubs.  
 
– Buttons, Connectors and Indicators –  
Remote  
Connections and  
Plug&Play Setting  
A Check contents  
Make sure the package contains all of the accessories listed in  
Specifications.  
Number keys  
B Attach the 4 feet as illustrated below  
If you want to place the VCR  
horizontally ...  
If you want to place the VCR  
vertically ...  
Do not attach the foot on the  
screw hole.  
Foot  
If you place the VCR  
vertically, attach the  
wire clamp to hold the  
AC power cord in  
place as shown at  
right.  
Stick the wire clamp on the rear of the  
VCR using the provided adhesive tape  
with two sides.  
On-screen display  
Slide the AC power cord into the wire  
clamp.  
If you press OSD on the Remote when SUPERIMPOSEis set to  
ON, you can see the current VCR status on the TV screen. Press  
OSD again to exit on-screen display.  
C Situate VCR  
The indications are not recorded even if the VCR is in the  
recording mode.  
Place the VCR on a stable, horizontal surface. Do not place the  
VCR in any other way than illustrated above.  
D Connect VCR to TV  
RF Connection  
CH125  
RECORD  
PAUSE  
SP  
THU 12:00 AM  
STEREO  
SAP  
A Disconnect the TV antenna from the TV.  
B Connect the TV antenna cable to the ANT. IN terminal on the  
rear of the VCR.  
C Connect the supplied RF cable between the TV OUT terminal  
on the rear of the VCR and the TVs antenna input terminal.  
+
+
+
E
1
B
INDEX  
AV Connection  
NORM  
HI-FI  
COUNT  
–1:23:45  
(improves picture quality during tape playback.)  
If your TV is equipped with audio/video input connectors  
A Connect the antenna, VCR and TV as shown in the illustration.  
B Connect an audio/video cable between the AUDIO/VIDEO  
OUT connectors on the rear of the VCR and the audio/video  
input connectors on the TV.  
Even if you are using audio/video cables to connect your VCR to  
your TV, you must also connect it using the RF cable. This will  
ensure that you can record one show while watching another.  
A Channel and auxiliary input  
B Day and clock time  
C STEREO program indication  
D SAP indication  
E Audio monitor indications  
F Time counter  
G Index number  
H Tape position  
I Cassette mark  
J Tape speed  
K VCR operation mode  
 
                                                                                           
                                                                                            
                                                                                               
                                                                                               
– Connections and Plug&Play Setting –  
F Set VCR channel  
To audio/video  
TV  
The VCR channel is the channel on which you can watch the  
picture from the VCR on the TV when only using the RF  
connection. Press POWER to turn off the VCR, then press STOP/  
EJECT (0) on the VCR for more than 5 seconds. CH3”  
appears on the display panel. Press CH+/– on the Remote to  
select CH3, CH4or CH–”(OFF), then press OK.  
The VCR channel is preset to CH3. Set to CH4if CH3 is  
used for broadcasting in your area.  
input connectors  
Audio/video cable  
(not supplied)  
RF cable  
To 75 terminal  
(supplied)  
G Final preparation for use  
Turn on the VCR and the TV, and select the VCR channel 3 or 4  
(or AV mode) on the TV. You can now perform basic playback or  
basic recording.  
AC power  
cord  
Initial Settings  
AC outlet  
Language Setting  
The default setting is ENGLISH.  
MAIN MENU  
A Access Main Menu screen, then  
FUNCTION SET  
Initial Set screen  
Back of VCR  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to INITIAL  
Matching transformer  
(not supplied)  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
Flat feeder  
B Select language  
INITIAL SET  
CLOCK SET  
This VCR offers you the language choice to  
view menus and some messages in  
English, Spanish or French. Press rt to  
move the highlight bar (arrow) to  
LANGUAGE, then press OK or e  
repeatedly until the desired language is  
selected.  
LANGUAGE  
ENGLISH  
GUIDE CHANNEL SET  
Coaxial cable  
Antenna or cable  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
E Perform Plug&Play setup  
Plug the AC power cord into an AC outlet. Do not turn on the  
VCR. The clock and tuner channels will be set automatically. The  
time and date can be set automatically by the clock setting data  
transmitted from one of the regular TV broadcast channels. We  
call this TV channel the host channeland it is a PBS channel in  
your area.  
Press MENU to return to normal screen.  
Clock Setting  
Perform clock setting only if the clock has not been set correctly  
by the Plug&Play setting or if you use a cable box.  
ATTENTION:  
If you use a cable box, Plug&Play will not function; set the clock  
and tuner channels separately.  
Preparations  
A Access Main Menu screen, then  
During Initial Auto Clock Set  
Autblinks.  
MAIN MENU  
FUNCTION SET  
Initial Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
During Auto Channel Set  
The channel numbers are displayed as they are  
scanned and set.  
move the highlight bar (arrow) to INITIAL  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
Plug&Play Completed  
B Access Clock Set screen  
Press rt to move the highlight bar  
(arrow) to CLOCK SET, then press OK or  
e.  
INITIAL SET  
CLOCK SET  
The current time is displayed.  
LANGUAGE  
ENGLISH  
GUIDE CHANNEL SET  
What to do if Plug&Play setting failed  
If an incorrect time is displayed on the display panel, perform  
the Semiauto Clock Setor Manual Clock Setprocedure.  
If “–:– –” appears on the display panel, ensure that the antenna  
cable is connected correctly. Then turn on and off the VCR; the  
Plug&Play setting will be automatically reactivated. If Plug&Play  
setting is not performed though the antenna cable is connected  
correctly, perform Manual Clock Setand Auto Channel Set”  
or Manual Channel Set.  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
Setting clock semiautomatically  
— Semiauto Clock Set  
You can change the host channel/D.S.T. (Daylight Saving Time)/  
time zone setting manually. First follow steps 1 to 2 in  
Preparationsabove, then go to the following steps.  
NOTE:  
The time set previously will be erased when “AUTO CLOCK”,  
“HOST CH”, “D.S.T.” or “TIME ZONE” setting is changed.  
 
                           
                           
                 
                 
                    
                    
– Initial Settings –  
CLOCK SET  
A Set Auto Clock to ON  
Tuner Setting  
TIME  
DATE  
12/24  
YEAR  
Press OK or e on the Remote repeatedly  
to move the highlight bar to AUTO  
CLOCK, then press rt so that ONis  
selected.  
1:00PM  
00 SUN  
AUTO CLOCK : ON  
HOST CH  
D.S.T.  
: AUTO  
: AUTO  
(CATV)  
Setting channels automatically  
— Auto Channel Set  
TIME ZONE : AUTO  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
Perform Auto Channel Set only if channels have not been set  
correctly by the Plug&Play setting.  
B Select host channel  
You can either select AUTOor enter a PBS channel number.  
Press OK or e to move the highlight bar to HOST CH, then  
press rt repeatedly until AUTOor the desired PBS channel  
number is selected.  
MAIN MENU  
A Access Main Menu screen, then Tuner  
FUNCTION SET  
Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to TUNER  
C Select D.S.T. mode  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
Press OK or e to move the highlight bar to D.S.T., then press  
rt repeatedly until the desired setting is selected.  
AUTO: Select if you want to adjust your VCRs clock  
automatically by the incoming signal from the host  
channel. (Auto Daylight Saving Time enables automatic  
adjustment of the VCRs clock at the start and end of  
Daylight Saving Time.) Be sure to select the correct time  
zone manually in step 4.  
PRESS (MENU) TO END  
B Perform Auto Channel Set  
TUNER SET  
BAND  
CATV  
Press rt to move the highlight bar  
(arrow) to AUTO CHANNEL SET, then  
press OK or e. The VCR selects the correct  
band (TV or CATV) automatically during  
Auto Channel Set.  
AUTO CHANNEL SET  
MANUAL CHANNEL SET  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
ON:  
OFF:  
Adjustment will be made by the built-in clock itself.  
Select when Daylight Saving Time does not apply to you.  
When Auto Channel Set is complete,  
SCAN COMPLETEDappears on  
screen.  
AUTO CHANNEL SET  
D Select time zone  
If the scan was unsuccessful, SCAN  
COMPLETEDNO SIGNAL–” appears  
on screen. Check the connections and  
start again.  
SCANNING...  
Press OK or e to move the highlight bar to TIME ZONE, then  
press rt repeatedly until AUTOor the desired time zone is  
selected. Each time you press the button, the time zone changes  
as follows:  
PRESS (MENU) TO END  
Press MENU to return to normal screen.  
{ AUTO { ATLANTIC { EASTERN { CENTRAL  
{ MOUNTAIN { PACIFIC { ALASKA { HAWAII  
{ (back to the beginning)  
Setting channels manually  
— Manual Channel Set  
E Complete Semiauto Clock Set  
You can add the channels you want or delete the channels you do  
not want manually.  
Press MENU to return to normal screen. Turn off the VCR. Aut”  
will appear on the display panel while the clock is being set. The  
current clock time will appear automatically when the clock  
setting is complete.  
MAIN MENU  
A Access Main Menu screen, then Tuner  
FUNCTION SET  
Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
Setting clock manually  
— Manual Clock Set  
move the highlight bar (arrow) to TUNER  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
First follow steps 1 to 2 in Preparationsabove, then go to the  
B Access Manual Channel Set screen  
Press rt to move the highlight bar  
(arrow) to MANUAL CHANNEL SET,  
then press OK or e.  
TUNER SET  
following steps.  
BAND  
CATV  
AUTO CHANNEL SET  
MANUAL CHANNEL SET  
CLOCK SET  
A Set time, date and year  
Press rt until the desired time appears,  
then press OK or e. Set the date and year  
in the same way.  
Holding rt changes the time in 30-  
minute intervals, or changes the date in  
15-day intervals.  
TIME  
– –:– –AM  
DATE  
1/  
YEAR  
00  
1
AUTO CLOCK : ON  
SELECT WITH (  
,
) AND (OK)  
HOST CH  
D.S.T.  
: AUTO  
: AUTO  
TIME ZONE : AUTO  
(CATV)  
PRESS (MENU) TO END  
MANUAL CHANNEL SET  
C Add or skip desired channels  
To add channels  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
(CATV)  
CH 45 ADD  
A Press the Number keys on the Remote  
to input a channel number you want to  
add.  
B Press OK or e to set to ADD.  
C Repeat A to B to add other channels.  
Press MENU to return to normal screen.  
To skip channels  
A Press rt or the Number keys to select a channel number you  
want to skip.  
B Press OK or e to set to SKIP.  
CLOCK SET  
B Select D.S.T. mode  
Press OK or e to move the highlight bar to  
D.S.T., then press rt to select the  
desired setting.  
ON: Adjustment will be made by the  
built-in clock itself.  
OFF: Select when Daylight Saving Time  
does not apply to you.  
PRESS NUMBER KEY (09)  
TIME  
1:00AM  
DATE  
YEAR  
00 SUN  
OR (  
,
), THEN (OK)  
12/ 24  
PRESS (MENU) TO END  
AUTO CLOCK : OFF  
D.S.T.  
: ON  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
C Repeat A and B to skip other channels. Press MENU to return  
to normal screen.  
C Start clock  
Press MENU and normal screen appears.  
To make corrections any time during the process  
Press OK or e repeatedly until the item you want to change  
blinks, then press rt.  
 
When the tape is not running  
Rewind/fast-forward at high speed  
Press REW (3) or FF (5).  
Eject the tape  
Playback  
Basic Playback  
A Load a cassette  
Make sure the window side is facing to the left,  
the rear label side is facing you and the arrow  
on the front of the cassette is pointing towards  
the VCR.  
Press STOP/EJECT (0).  
You can also eject the cassette when the VCR is turned off.  
Turn off the VCR  
Press POWER.  
Do not apply too much pressure when  
inserting.  
The VCR turns on, and the counter on the  
on-screen display is reset, automatically.  
If the cassettes record safety tab has been  
removed, playback begins automatically.  
Playback Features  
Adjusting tracking condition  
Tracking Adjustment  
Automatic tracking adjustment  
Whenever you insert a tape and start playback, automatic tracking  
starts working and continuously analyzes the signal to enable  
optimum picture quality during playback.  
B Start playback  
Press PLAY (4).  
Manual tracking adjustment  
If automatic tracking cannot eliminate noises well during  
playback, follow the procedures below.  
During playback  
Stop playback  
A Press SP/EP on the Remote during playback to activate manual  
tracking.  
B Press CH + and to eliminate the noises. Press it briefly for a  
Press STOP (8) on the  
Remote.  
OR Press STOP/EJECT (0) on  
the VCR.  
fine adjustment, or press and hold for a coarse adjustment.  
C Press SP/EP on the Remote again to reactivate automatic  
Pause playback and view still picture  
tracking.  
Press PAUSE (9).  
Press PLAY (4) to resume normal playback.  
Selecting monitor sound  
— Audio Monitor  
Pause and Frame-by-Frame playback  
Press PAUSE (9) to pause, then press 2 or 6 (or PAUSE (9))  
repeatedly.  
Press PLAY (4) to resume normal playback.  
While playing back a tape on which stereo sound or SAP sound is  
recorded, press A. MONITOR on the Remote. Each time you press  
the button, sound changes.  
Rewind/fast-forward  
HI-FI: Normally select this. Hi-Fi sound is played back.  
HI-FI L: Sound on the left Hi-Fi channel is played back.  
HI-FI R: Sound on the right Hi-Fi channel is played back.  
NORM: Sound on the normal track is played back.  
NORM HI-FI: Both sounds on the Hi-Fi track and normal track are  
mixed and played back.  
Press REW (3) or FF (5).  
Press PLAY (4) to resume normal playback.  
If you press and hold REW (3) or FF (5) for more than  
2 seconds, simply releasing it cancels the picture search, and  
normal playback resumes.  
NOTE:  
Rewind/fast-forward at variable speed (including slow-motion)  
The above indication appears when “SUPERIMPOSE” is set to  
“ON”, though the monitor sound changes in sequence.  
Press 2 or 6 repeatedly.  
Press PLAY (4) to resume normal playback.  
Each time you press 2 or 6, the playback speed changes.  
To decrease the speed during picture search, press the opposite  
direction button repeatedly.  
During still picture, press and hold 6 to start forward (or  
2 to start reverse) slow motion playback. When you release  
the button, still picture resumes. During still picture, holding  
PAUSE (9) for more than 2 seconds also starts forward slow  
motion playback. If you press PAUSE (9) again, still picture  
resumes.  
Automatic operations after rewinding  
— Next Function Memory  
The Next Function Memory tellsthe VCR what to do after  
rewinding is complete. Ensure that the VCR is in stop mode.  
For Automatic Playback Start  
Press REW (3), then press PLAY (4) within 2 seconds.  
For Automatic Power Off  
Press REW (3), then press POWER within 2 seconds.  
For Automatic Timer Standby  
Press REW (3), then press TIMER within 2 seconds.  
NOTE:  
It is not possible to select the Automatic Timer Standby function if  
the cassettes record safety tab is removed.  
Reverse  
Forward  
Reverse  
slow  
motion  
5 steps  
Reverse Reverse  
Slow  
motion  
5 steps  
Normal Forward  
search  
3 steps  
play  
play  
search  
4 steps  
 
– Playback –  
Playing back tape repeatedly (100 times)  
— Repeat Play  
Recording  
It may be unlawful to record or play back copyrighted material  
without the consent of the copyright owner.  
During playback, press and hold PLAY (4) for more than  
5 seconds. The PLAYdisplay on the on-screen display starts  
blinking. To stop playback, press STOP (8) on the Remote or  
STOP/EJECT (0) on the VCR.  
Accidental erasure prevention  
To prevent accidental recording on a  
recorded cassette, remove its record  
safety tab. To record on it later, cover  
Locating beginning of recordings  
— Index Search  
the hole with adhesive tape.  
Record safety tab  
Index codes are placed on the tape at the beginning of each  
recording when recording on this VCR.  
Basic Recording  
A Load a cassette  
A While the tape is not running, press SHUTTLE PLUS 2 or  
6 on the Remote to start search.  
B To access a recording of 2 to 9 index  
codes away, press 2 or 6  
Make sure the record safety tab is intact. If not, cover the hole  
with adhesive tape before inserting the cassette.  
repeatedly until the correct number is  
displayed on the screen (only if  
SUPERIMPOSEis set to ON).  
Playback begins automatically when  
the desired recording is located.  
The VCR turns on, and the counter is reset, automatically.  
B Select recording channel  
On the Remote  
Press CH+/– or the Number keys.  
On the VCR  
INDEX  
1
Press PAUSE[CH]. The channel display on the  
display panel starts blinking. While the display is  
blinking, press FF[CH+] or REW[CH–] to select  
channel. After about 5 seconds, the channel display  
stops blinking.  
Beginning of the  
current program  
recorded  
Beginning of the  
2nd next program  
recorded  
Current  
position on  
the tape  
Previous  
program  
recorded  
Next  
program  
recorded  
2nd next  
NOTES:  
You can select channel in the stop mode,  
recording pause mode or during rewind/fast-  
forward high-speed search.  
If no cassette is loaded, or during recording pause  
mode, you can select channel only by pressing  
FF[CH+] or REW[CH–].  
If you connect the TV and the VCR only using the  
RF connection, press TV/VCR on the Remote so  
that the VCR mode indicator lights on the display  
panel, to view the program to be recorded.  
Locating beginning of timer recordings  
— Instant Review  
After ensuring that the VCR is turned off and that the timer mode  
is disengaged, press REVIEW on the Remote.  
The VCR turns on, and rewinds to the index code indicating the  
beginning of the last timer-recorded program, then begins  
playback automatically.  
C Set tape speed  
Press SP/EP.  
D Start recording  
You can access a program of 2 to 9 index codes away from the  
current position on the tape. If, for example, you have  
5 programs recorded and you want to watch the third one, press  
REVIEW three times.  
On the VCR, press REC (7). Or on the Remote, while holding REC  
(7), press PLAY (4).  
The Instant Review function will also operate if the VCR is  
turned on.  
During recording  
Pause recording  
Skipping unwanted portions  
— Skip Search  
Press PAUSE (9).  
Press PLAY (4) to resume recording.  
You can select channel in the recording pause mode.  
Press SKIP SEARCH on the Remote 1 to 4 times during playback.  
Each press initiates a 30-second period of high speed playback (up  
to 2 minutes). When the specified portion of the tape is skipped,  
normal playback resumes automatically. To return to normal  
playback during Skip Search, press PLAY (4).  
Stop recording  
Press STOP (8) on the  
Remote.  
OR Press STOP/EJECT (0) on  
the VCR.  
 
                                                                      
                                                                      
                                                                           
                                                                           
– Recording –  
Recording Features  
Timer Recording  
Up to 8 timer recording programs can be made using VCR Plus+  
timer programing or Express timer programing method as far as a  
year in advance. Remember, the clock must be set before you can  
program the timer.  
Specifying recording length  
— Instant Timer Recording (ITR)  
During recording, press REC (7) on the VCR repeatedly until the  
recording length you want appears on the display panel. The REC  
indicator on the display panel starts blinking.  
NOTES:  
If all the 8 programs have already been set, “PROGRAM FULL”  
or “Full” appears on the TV screen or the display panel.  
After timer recording is completed, the VCR turns off  
automatically.  
Each time you press the button, recording length increases in  
30-minute intervals (up to 6 hours).  
The VCR shuts off after recording is finished.  
To cancel an ITR, press STOP (8) on the Remote or STOP/EJECT  
(0) on the VCR.  
You can program the timer recording while a regular recording  
is in progress; the menu screens will not be recorded.  
To timer-record cable or satellite channels, be sure to keep the  
cable box or DBS receiver turned on with the correct channel  
selected.  
In case of a power failure after programming, the VCRs memory  
backup keeps your selections for approximately 10 minutes.  
Watching one program while recording another  
During recording…  
If you connect the TV and the VCR only using the RF  
connection to view pictures from the VCR, press TV/VCR on the  
Remote so that VCR mode indicator goes off from the display  
panel. (The TV broadcast being recorded disappears.)  
If you are using the AV connection to view pictures from the  
VCR, change the TVs input mode from AV to TV.  
Then, select the channel you want to watch, on the TV.  
Changing VCR Plus+® Setting  
The VCR Plus+ programing system assigns a VCR Plus+ guide  
channel to the TV channels and the cable channels. These guide  
channel numbers are also called the VCR Plus+ channel codes.  
Most TV listings have a section, usually a chart, indicating the  
guide channel numbers assigned to each station.  
Second Audio Recording  
This VCRs built-in MTS decoder enables reception of  
Multichannel TV Sound broadcast. To record a SAP program  
received, set 2ND AUDIO RECORDto ON.  
To ensure that VCR Plus+ timer recording operates correctly, it is  
necessary to set the VCR Plus+ Guide Channel Setfor each  
station.  
If you have moved to a different area or if a broadcasting stations  
channel number has been changed, perform the following steps to  
set the correct guide channel number.  
MAIN MENU  
A Access Main Menu screen, then  
FUNCTION SET  
Initial Set screen  
TUNER SET  
INITIAL SET  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to INITIAL  
SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Access Guide Channel Set screen  
Press rt to move the highlight bar  
(arrow) to GUIDE CHANNEL SET, then  
press OK or e.  
INITIAL SET  
CLOCK SET  
LANGUAGE  
ENGLISH  
GUIDE CHANNEL SET  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
GUIDE CHANNEL SET  
C Input guide channel number  
GUIDE CH :  
VCR CH  
6
Press rt or the Number keys to select  
the VCR Plus+ guide channel number as  
shown in the TV listing, then press OK or  
e.  
:
– – –  
PRESS NUMBER KEY (09)  
OR (  
,
), THEN (OK)  
PRESS (MENU) TO END  
GUIDE CHANNEL SET  
D Input receiving channel number  
GUIDE CH :  
VCR CH  
6
47  
Press rt or the Number keys to select  
the number of the channel on which the  
guide channels broadcasts are received,  
then press OK or e.  
:
PRESS NUMBER KEY (09)  
OR ( ), THEN (OK)  
PRESS (MENU) TO END  
,
Repeat steps 3 and 4 for each instance.  
E Return to normal screen  
Press MENU on the Remote.  
 
– Timer Recording –  
VCR Plus+® Timer Programing  
Express Timer Programing  
The PlusCode programing numbers are the numbers next to the  
program in most TV listing.  
Load a cassette with the record safety tab intact. The VCR turns  
on, and the counter is reset, automatically.  
Load a cassette with the record safety tab intact. The VCR turns  
on, and the counter is reset, automatically.  
A Press PROG. on the Remote to access the PlusCode No.  
screen.  
A Press PROG. on the Remote to access  
PLUSCODE NO.  
B Press START+/– once to access  
PROGRAM 1  
the PlusCode No. screen.  
Program screen. Press START+/–,  
START  
– –:– –AM  
DATE  
STOP  
– –:– –AM  
CH  
STOP+/–, DATE+/– or CH+/–  
repeatedly to enter the start time, stop  
time, date or channel.  
– –/– –/– –  
– – – SP  
PRESS NUMBER KEY (09)  
PRESS (+/) TO SET  
EXPRESS PROGRAMMING  
PRESS (PROG.) TO END  
PRESS (+/, SP/EP, 8=DAILY  
9=WEEKLY), THEN (0K)  
PRESS (PROG.) TO END  
Press and hold START+/– or  
STOP+/– to increase the time in  
30-minute intervals.  
B Press the appropriate Number keys to input the PlusCode  
number, then press OK. Check to make sure the setting is  
accurate on the Program screen.  
To set the tape speed, press SP/EP.  
To timer-record daily (MondayFriday) or weekly serials,  
press DAILY (M-F) or WEEKLY. Pressing the button again  
makes the DAILYor WEEKLYdisplay disappear.  
PROGRAM 1  
PLUSCODE NO.  
(PLUSCODE NO. 12345678)  
START  
8:00PM  
DATE  
12/24/00  
SUN  
STOP  
10:00PM  
CH  
1 2 3 4 5 6 7 8  
C Press OK or PROG..  
12 SP  
D Press TIMER. The VCR turns off automatically and #is  
PRESS NUMBER KEY (09)  
THEN (OK)  
PRESS (PROG.) TO END  
PRESS (8=DAILY, 9=WEEKLY  
STOP+/= STOP TIME, SP/EP)  
PRESS (OK) TO END  
displayed on the display panel.  
If the Guide Channel Set screen  
appears after pressing OK, press the  
Number keys, CH+/– or rt to  
input the number of the channel on  
which the broadcast for the PlusCode  
number is received on the VCR, then  
press OK.  
GUIDE CHANNEL SET  
GUIDE CH : 12  
VCR CH  
:
– – –  
PRESS NUMBER KEY (09)  
OR ( ), THEN (OK)  
PRESS (PROG.) TO END  
,
To set the tape speed, press SP/EP.  
To change the stop time, press STOP+/–.  
To timer-record daily (MondayFriday) or weekly serials,  
press DAILY (M-F) or WEEKLY. Pressing the button again  
makes the DAILYor WEEKLYdisplay disappear.  
If you made a mistake, press CANCEL to access the  
PlusCode No. screen again.  
If an incorrect PlusCode number or the one for a broadcast  
already finished has been inputted, ERRORis displayed for  
about 5 seconds, then the PlusCode No. screen reappears.  
C Press OK or PROG..  
D Press TIMER. The VCR turns off automatically and #is  
displayed on the display panel.  
 
– Timer Recording –  
To use the VCR while it is in timer  
recording standby mode  
Other Functions  
Press TIMER, then press POWER. After you use the VCR, press  
Checking tape position  
TIMER again to put the VCR into timer recording standby mode.  
When you change the VCR operation  
mode from the stop mode to fast forward  
or rewind mode, or when you perform an  
Index Search or Instant Review, the tape  
Checking, canceling or changing  
program settings  
A Disengage timer  
Press TIMER, then press POWER.  
+
+
+
E
B
position indicator appears.  
The position of qin relation to B”  
(Beginning) or E(End) shows you where  
you are on the tape.  
Set SUPERIMPOSEto ON.  
When AUTO TIMERis set to ON, you do not have to press  
TIMER.  
Resetting time counter  
B Access Program Check screen  
Press PROG. CHECK.  
PR START STOP CH DATE  
1
2
3
4
5
6
7
8
8:00P 10:00 12 12/24  
10:00A 10:45 40 12/25  
When SUPERIMPOSEis set to ONand DISPLAY on the  
Remote is pressed, the on-screen display will appear for about  
5 seconds on the TV screen. While the display is shown, press  
11:30P  
1:00 125 12/25  
C. RESET on the Remote to reset the time counter to 00:00:00.  
PRESS (CHECK) TO NEXT  
PROGRAM 1  
C Access Program screen  
Press PROG. CHECK again. Each time you  
press PROG. CHECK, the next programs  
Program screen appears.  
Function settings  
START  
8:00 AM  
DATE  
STOP  
10:00 AM  
CH  
You can use the other useful function settings on the Function Set  
screen.  
12/24/00  
12 SP  
PRESS (CANCEL) TO CANCEL  
PRESS (CHECK) TO NEXT  
MAIN MENU  
A Access Main Menu screen, then  
FUNCTION SET  
D Cancel or change program setting  
Function Set screen  
TUNER SET  
INITIAL SET  
To cancel a program, press CANCEL when the Program screen  
you do not want is shown.  
To change a program, press the appropriate button: START+/–,  
STOP+/–, DATE+/–, CH+/–, and/or SP/EP when the Program  
screen on which you want to make changes is shown.  
Press MENU on the Remote. Press rt to  
move the highlight bar (arrow) to  
FUNCTION SET, then press OK or e.  
PRESS (  
,
), THEN (OK)  
PRESS (MENU) TO END  
B Select Function  
FUNCTION  
PICTURE CONTROL  
AUTO TIMER  
E Return to normal screen  
NORM  
OFF  
ON  
Press rt to move the highlight bar  
SUPERIMPOSE  
Press PROG. CHECK repeatedly until no Program screen is  
(arrow) to the function you want to set.  
AUTO SP EP TIMER  
VIDEO STABILIZER  
2ND AUDIO RECORD  
AUDIO MONITOR  
OFF  
OFF  
OFF  
HI-FI  
shown.  
F Reengage timer recording standby mode  
Press TIMER. The VCR turns off automatically and #is  
displayed on the display panel.  
SELECT WITH (  
,
) AND (OK)  
PRESS (MENU) TO END  
When AUTO TIMERis set to ON, the timer recording  
standby mode automatically resumes when you turn off the  
VCR.  
 
– Other Functions –  
C Change setting  
VIDEO STABILIZER — ON/OFF  
When this function is set to ON, you can automatically correct  
vertical vibrations in the picture when playing back unstable  
recordings made on another VCR.  
Press OK or e. The default setting is bold in the following table.  
Press MENU to return to normal screen.  
NOTE:  
PICTURE CONTROL NORM/EDIT/SOFT/SHARP  
This function helps you to adjust the playback picture quality  
according to your preference.  
To watch recordings with close-caption or when you finish  
viewing a tape, set this function to “OFF”.  
NORM: Normally select this. Picture quality is adjusted  
automatically.  
EDIT: Minimizes picture degradation during editing (recording and  
playback).  
SOFT: Reduces image coarseness when viewing overplayed tapes  
containing much noise.  
SHARP: Clearer, sharper-edged picture when viewing images with  
much flat, same-colored surfaces such as cartoons.  
2ND AUDIO RECORD — ON/OFF  
When this function is set to “ON”;  
If a SAP program is received, the SAP audio is recorded on both  
the normal and Hi-Fi tracks. The main audio is not recorded.  
If a non-SAP program is received, the main audio is recorded on  
both the Hi-Fi and normal tracks.  
When this function is set to “OFF”, the SAP audio cannot be  
recorded.  
NOTE:  
Select “EDIT” when you are editing tapes. After you finish editing  
the tapes, select “NORM”.  
NOTES:  
When the channel is changed on the VCR;  
The “STEREO” indication appears on the screen for about  
5 seconds if the program is a stereo broadcast.  
The “SAP” indication appears on the screen for about  
5 seconds if the program is a SAP broadcast.  
Both indications appear when a stereo program is accompanied  
by SAP sound.  
AUTO TIMER — ON/OFF  
When this function is set to “ON”:  
The timer recording standby mode is automatically engaged when  
the VCR is turned off. It is temporarily canceled when the VCR is  
turned on. You do not have to press TIMER to engage or disengage  
the timer recording standby mode.  
When this function is set to “OFF”:  
You have to press TIMER to engage or disengage the timer  
recording standby mode.  
AUDIO MONITOR HI-FI/HI-FI L/HI-FI R/NORM/MIX  
This VCR can record two sound tracks simultaneously (normal  
and Hi-Fi) on a Hi-Fi stereo tape. You can select the sound track(s)  
to listen to while playing back a Hi-Fi stereo tape. In addition,  
when playing back a prerecorded tape containing two separate  
audio programs on the Hi-Fi tracks, you can choose either one by  
selecting either HI-FI Lor HI-FI R.  
HI-FI: Normally select this. Hi-Fi sound is played back.  
HI-FI L: Sound on the left Hi-Fi channel is played back.  
HI-FI R: Sound on the right Hi-Fi channel is played back.  
NORM: Sound on the normal track is played back.  
SUPERIMPOSE ON/OFF  
When this function is set to ON, various VCR status information  
(on-screen display) appears on the screen.  
NOTE:  
When you use this VCR as the playback VCR for editing a tape, be  
sure to set this function to “OFF”; otherwise, the VCR status  
information (on-screen display) will be recorded on the edited  
tape.  
MIX: Both sounds on the Hi-Fi track and normal track are mixed  
and played back.  
NOTES:  
While playing back a monaural tape, sounds on the normal  
track will be heard regardless of this setting.  
If RF connection is used for viewing pictures on the TV, sound  
will be monaural even though you select “HI-FI”.  
You can also use the A. MONITOR button on the Remote to  
select the desired monitor sound.  
AUTO SP]EP TIMER — ON/OFF  
When this function is set to ON, the VCR automatically  
switches to EP mode to allow complete recording if there is not  
enough tape to record the entire program while timer-recording in  
SP mode.  
For Example, Recording a program of 140 minutes in length onto  
a 120-minute tape  
Approximately 110 minutes  
Approximately 30 minutes  
SP mode  
EP mode  
NOTES:  
If you have programed the VCR to timer-record 2 or more  
programs, do not use this function, but change the tape speed  
manually during timer programing.  
There may be some noise and sound disturbance where the  
tape speed switches from SP to EP mode on the tape.  
This function is not available during ITR (Instant Timer  
Recording), and will not work properly on the following tapes:  
T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.  
 
                                                                              
                                                                              
                                                                                             
                                                                                             
                                                                           
                                                                           
                                                                             
                                                                             
                                                                                  
                                                                                  
– Other Functions –  
CABLE BOX BRAND  
CODE  
Multi-Brand Remote Control  
ARCHER  
01, 05, 17  
This Remote can control some functions of remote controllable  
TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers  
listed below. Without setting, you can control a JVC TV.  
CABLETENNA  
CABLEVIEW  
CITIZEN  
01, 17  
15, 16, 17, 21, 25  
15, 16, 17, 21, 25  
CURTIS  
02  
NOTES:  
DIAMOND  
EASTERN  
01, 17  
Some units brands have more than one code. If the unit does  
not function with a specified code, try other codes.  
Depending on the type of unit, some or all functions cannot be  
operated using this Remote.  
19  
GC BRAND  
GEMINI  
15, 16, 17, 21, 25  
15  
GENERAL INSTRUMENTS  
HAMLIN  
01, 04, 06, 11, 12, 15, 28  
Its not possible to operate a unit not equipped with a remote  
sensor.  
Its not possible to set the Remote for both your cable box and a  
DBS receiver at the same time.  
Once you have set the Remote to operate the unit, you do not  
have to set it until you replace the batteries from the Remote.  
10, 18, 19, 23  
JASCO  
15  
JERROLD  
01, 04, 06, 11, 12, 15, 28  
NOVAVISION  
OAK  
02  
07  
PANASONIC  
PULSER  
13, 14  
15, 16, 17, 21, 25  
13, 14  
RCA  
REGAL  
10, 18, 19, 23  
19  
TV Brand Setting  
REGENCY  
REMBRANDT  
SAMSUNG  
SCIENTIFIC ATLANTA  
SIGMA  
01, 16, 17  
05, 16, 24  
02  
A Turn on TV  
Turn on the TV using the Power button on the TV or its Remote.  
07  
B Set TV brand code  
SL MARX  
05, 16, 17, 24, 25  
13, 14  
A Press and hold TV.  
SPRUCER  
STARGATE  
TELEVIEW  
TOCOM  
B Press MBR SET.  
05, 15, 16, 17, 21, 24, 25  
05, 16, 24  
01, 04, 16  
01, 17  
C Press the Number keys to enter your TVs brand code.  
D Press OK, and release TV. The TV should turn off.  
UNIKA  
C Operate TV  
UNIVERSAL  
VIDEOWAY  
ZENITH  
16, 17, 25  
03, 09, 22  
03, 09, 22  
While holding down TV, press one of the following buttons:  
POWER, TV/VCR, TV CH+/–, ^ (TV Muting), TV VOL+/–, and  
the Number keys.  
DBS RECEIVER BRAND  
CODE  
For some brands, you must press ENTER after having pressed the  
Number keys to enter a channel number.  
JVC (DISH Network)  
ECHOSTAR (DISH Network)  
PRIMESTAR  
SONY (DSS)  
RCA (DSS)  
51  
51  
50  
41  
40  
TV BRAND  
CODE  
TV BRAND  
CODE  
JVC  
01, 03  
10  
SONY  
07  
12  
13  
13  
08  
09  
HITACHI  
MAGNAVOX  
MITSUBISHI  
PANASONIC  
RCA  
SAMSUNG  
SANYO  
SEARS  
02  
03  
04, 11  
05  
TOSHIBA  
ZENITH  
Changing Remote Control Code  
SHARP  
06  
This Remote is capable of transmitting two control codes; one set  
to respond to A code control signals and another set to respond to  
B code control signals. This Remote control is preset to send A  
code signals because your VCR is initially set to respond to A  
code signals. You can easily modify your VCR and the Remote to  
respond to B code signals. When using two JVC VCRs, set two  
VCRs and their Remotes to different codes, so that you can  
operate these VCRs separately.  
Cable Box or DBS Receiver Brand Setting  
A Turn on cable box or DBS receiver  
Turn on the cable box or DBS receiver using the Power button on  
the unit or its Remote.  
B Enter brand code  
A Press and hold CABLE/DBS.  
B Press MBR SET.  
A Unplug VCR  
Unplug the AC power cord from the AC outlet.  
C Press the Number keys to enter your cable boxs (or DBS  
receivers) brand code.  
B Set remote control code for Remote  
A Press and hold A/B.  
D Press OK, and release CABLE/DBS.  
B Press the Number key 2.  
C Press OK, and release A/B.  
The Remote now can transmit B code control signals.  
C Operate cable box or DBS receiver  
While holding down CABLE/DBS, press one of the following  
buttons: POWER, TV CH+/–, and the Number keys.  
For some brands, you must press ENTER after having pressed the  
Number keys to enter a channel number.  
C Plug in VCR  
Plug the AC power cord back into an AC outlet.  
To change the cable boxs (or DBS receivers) channels, press TV  
CH+/– or the Number keys. (The CH+/– button can be used to  
change the VCRs channels only.)  
D Turn on VCR  
Press POWER on the Remote.  
The VCR now responds to B code control signals.  
To set the Remote and the VCR back to A code control signals,  
repeat the same procedure as shown above except pressing the  
Number key 1in step B.  
To control two VCRs with the same Remote  
You can control two JVC VCRs by switching the remote control  
code for the Remote between A and B (step B), keeping two  
VCRs to different control codes.  
To change only the remote control code for the Remote, DO  
NOT perform steps A, C, and 4.  
 
                            
                            
Editing  
Specifications  
You can use your VCR as the playback or recording VCR. You can  
use a camcorder as the playback VCR and your VCR as the  
recording VCR. Refer also to the other componentsinstruction  
manuals for connection and its operations.  
GENERAL  
Power requirement  
Power consumption  
Power on  
: AC 120 Vd, 60 Hz  
A Make connections  
Example: When using this VCR as the playback VCR  
: 19 W  
: 1.8 W  
Power off  
Temperature  
Operating  
Storage  
Operating position  
: 5°C to 40°C (41°F to 104°F)  
: 20°C to 60°C (4°F to 140°F)  
: Horizontal or vertical  
This VCR (for playback)  
To AUDIO/VIDEO OUT  
Dimensions (W x H x D) : 275 mm x 100 mm x 275 mm  
(10-7/8" x 3-15/16" x 10-7/8")  
Weight  
: 3.6 kg (7.9 lbs)  
Format  
: VHS NTSC standard  
Maximum recording time  
Audio/video cable  
(not supplied)  
SP  
EP  
: 210 min. with ST-210 video cassette  
: 630 min. with ST-210 video cassette  
VIDEO/AUDIO  
Signal system  
:
NTSC-type color signal and EIA  
monochrome signal, 525 lines/  
60 fields  
To audio/video input  
Recording/Playback  
system  
Signal-to-noise ratio  
Horizontal resolution  
Frequency range  
Normal audio  
:
DA-4 (Double Azimuth) head helical  
scan system  
45 dB  
Another VCR (for recording)  
:
:
230 lines  
When using this VCR as the recording VCR, connect this VCRs  
audio/video input connectors to the audio/video output  
connectors on the other VCR. If the playback VCR is monaural,  
connect the audio output connector on the playback VCR to the  
left audio input connector on this VCR.  
:
:
:
70 Hz to 10,000 Hz  
20 Hz to 20,000 Hz  
RCA connectors (IN x 1, OUT x 1)  
Hi-Fi audio  
Input/Output  
B Load cassettes  
TUNER  
Insert the playback cassette into the playback VCR and the  
cassette to be recorded on into the recording VCR.  
Tuning system  
Channel coverage  
VHF  
: Frequency-synthesized tuner  
C Select input mode on recording VCR  
: Channels 213  
: Channels 1469  
: 113 Channels  
: Channel 3 or 4 (switchable; preset to  
Channel 3 when shipped) 75 ohms,  
unbalanced  
Select the correct external input on the recording VCR.  
On this VCR (when using this VCR as the recording VCR);  
Select L-1” — when connecting the other VCR to the audio/video  
input connectors on the rear panel.  
Press AUX or CH+/– on the Remote. You can select the input  
mode also by pressing PAUSE[CH], and then FF[CH+] or  
REW[CH–] on the VCR. See step B in Basic Recording.  
UHF  
CATV  
RF output  
TIMER  
D Select edit mode  
Clock reference  
Program capacity  
:
:
Quartz  
Set the edit mode to ONfor the VCRs if such a mode is  
equipped.  
1-year programmable timer/  
8 programs  
On this VCR, set PICTURE CONTROLto EDIT.  
Memory backup time  
:
Approx. 10 min.  
E Start playback  
Press PLAY (4) on the playback VCR.  
ACCESSORIES  
F Start recording  
Press REC (7) on the recording VCR.  
Provided accessories  
: RF cable (F-type),  
Infrared remote control unit,  
AAbattery x 2,  
Foot x 4,  
Wire clamp,  
Adhesive tape with two sides  
Specifications shown are for SP mode unless specified otherwise.  
E. & O.E. Design and specifications subject to change without  
notice.  
 
FOR SERVICING (Only in U.S.A.)  
HOW TO LOCATE YOUR JVC SERVICE CENTER  
TOLL FREE: 1-800-537-5722  
Dear Customer,  
In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the  
unit. In the event that repair is necessary, or for the address nearest your location within the Continental United States,  
retain your Bill of Sale for Warranty Service.  
— JVC  
JVC SERVICE & ENGINEERING  
COMPANY OF AMERICA  
DIVISION OF JVC AMERICAS CORP.  
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and  
production of the wide array of JVC products, service is the key to maintaining the high level performance for which JVC  
is world famous. The JVC service and engineering organization stands behind our products.  
NATIONAL HEADQUARTERS  
JVC SERVICE & ENGINEERING COMPANY OF AMERICA  
DIVISION OF JVC AMERICAS CORP.  
10 New Maple Avenue  
Pine Brook, NJ 07058-9641  
ACCESSORIES  
Don’t service the product yourself.  
To purchase accessories for your JVC product, you  
may contact your local JVC Dealer.  
From the 48 Continental United States call toll free:  
CAUTION  
To prevent electrical shock, do not open the cabinet.  
There are no user serviceable parts inside.  
Please refer to qualified service personnel for repairs.  
 
WARRANTY (Only in U.S.A.)  
LIMITED WARRANTY  
CONSUMER VIDEO 1-90  
JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL  
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail  
purchase for the period as shown below. (“The Warranty Period”)  
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN  
COMMONWEALTH OF PUERTO RICO.  
WHAT WE WILL DO:  
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and  
replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for  
replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC  
authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered  
on an in-home basis.  
WHAT YOU MUST DO FOR WARRANTY SERVICE:  
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service  
center, please call toll free: (800) 537-5722.  
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of  
sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be  
given to you by the toll-free number.  
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.  
WHAT IS NOT COVERED:  
This limited warranty provided by JVC does not cover:  
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,  
lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service,  
or if affixed to any attachment not provided with the products, or if the model or serial number has been altered, tampered with,  
defaced or removed;  
2. Initial installation and installation and removal for repair;  
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;  
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;  
5. Signal reception problems and failures due to line power surge;  
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;  
7. Accessories;  
8. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);  
There are no other express warranties except as listed above.  
THE DURATION OF ANY IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED  
TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.  
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER  
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES,  
RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS  
WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.  
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts,  
so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other  
rights which vary from state to state.  
JVC COMPANY OF AMERICA  
DIVISION OF JVC AMERICAS CORP.  
1700 Valley Road  
Wayne, New Jersey 07470  
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF  
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION  
PACKAGED WITH EACH REFURBISHED PRODUCT.  
For customer use:  
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this information  
for future reference.  
Model No.:  
Serial No.:  
Purchase date:  
Name of dealer:  
 

Intel Server S3000PT User Manual
JBL Car Speaker GTO1014 User Manual
Jenn Air Oven 8101P485 60 User Manual
JVC Flat Panel Television GM H40L1G User Manual
JVC Stereo System CA MXG500R User Manual
Kathrein Satellite TV System UFD 510 User Manual
Kawasaki Motorcycle Ninja User Manual
Kenmore Gas Grill 14116223 User Manual
Kicker Speaker S10XSP User Manual
KitchenAid Mixer KV25G0XBU5 User Manual